Just published.
The newest CVEs, straight from CVE.org and NVD.
-
CVE-2026-102815
An operating-system command injection vulnerability exists in the tmpServer service of TP-Link RE305 V3. The service runs with root privileges and listens on the local loopback interface. A local attacker with access to a low-privileged process on the device may submit a crafted request to the TDDPv1 service and execute operating-system commands with root privileges. Successful exploitation may allow a local attacker with low privileges to obtain root privileges and execute arbitrary operating-system commands on the affected device.
-
CVE-2026-102816
An authorization vulnerability exists in the country or region configuration interface of TP-Link RE305 V3. An unauthenticated attacker on the same local network may modify the wireless regulatory region and force the device to reapply its wireless configuration. Successful exploitation may cause wireless connection interruptions, unavailable channels, client disconnections, or wireless service instability, and may cause the device to apply parameters intended for a different regulatory region.
-
CVE-2026-102812
A hard-coded cryptographic key vulnerability exists in the user-configuration backup mechanism of TP-Link RE305 V3 and Archer C7 V5. A fixed AES-128 key and initialization vector are embedded in the firmware configuration-management component. An attacker who obtains an affected configuration backup file may extract the cryptographic material from the firmware and use it to decrypt the backup. Successful exploitation may disclose sensitive configuration information contained in a backup file, including administrator passwords and Wi-Fi credentials.
-
CVE-2026-102813
An authentication flaw exists in the password-recovery functionality of TP-Link RE305 V3. The verification-code interface allows an unauthenticated attacker on the same local network to trigger generation of an administrator password-reset verification code. Because the interface lacks an effective attempt counter or lockout mechanism and uses a predictable verification-code generation process, an attacker may obtain or brute-force the code and reset the administrator password. Successful exploitation may allow an unauthenticated attacker on the local network to reset the administrator password and subsequently access privileged device-management functions.
-
CVE-2026-93866
An integer overflow vulnerability in the WebSocket connection handling used by WatchGuard Fireware OS's Access Portal allows a remote, unauthenticated attacker to write beyond the bounds of a heap buffer by sending a specially crafted request while the Access Portal feature is enabled.
-
CVE-2026-93434
An XPath injection vulnerability in WatchGuard Fireware OS's SSH authentication process allows a remote, unauthenticated attacker with access to the management SSH interface to extract sensitive configuration data by submitting a specially crafted request.
-
CVE-2026-93857
A stack-based buffer overflow vulnerability in Fireware OS's SIP proxy allows a remote, unauthenticated attacker to execute arbitrary code by sending a specially crafted request through a policy that uses the SIP proxy.
-
CVE-2026-93862
An out-of-bounds read vulnerability in the FireCluster Sync processing allows an attacker positioned on the cluster interconnect, such as a compromised cluster peer or an on-path network attacker, to repeatedly crash the firewall's cluster synchronization process by sending specially crafted network traffic, resulting in a sustained denial of service.
-
CVE-2026-93864
A link following vulnerability in WatchGuard Fireware OS’s firewall daemon allows a local attacker with code execution as a low-privileged system process to overwrite arbitrary files with root privileges, and to tamper with firewall IP set data, by planting a crafted file system object and triggering a list update. Written content is partially constrained.
-
CVE-2026-82332
An improper authentication vulnerability in WatchGuard Fireware OS's AuthPoint multi-factor authentication process allows a local, unauthenticated attacker on the appliance to hijack another user's in-progress MFA session by supplying a specially crafted request and convincing the victim user to accept an MFA push notification.
-
CVE-2026-90442
A stack-based buffer overflow vulnerability in the Fireware OS certd process allows an authenticated attacker with access to the Firebox management interface to crash the certificate management service and potentially execute arbitrary code by sending a specially crafted request.
-
CVE-2026-90464
An external control of file path vulnerability in a WatchGuard Fireware OS firewall diagnostic command allows a remote, authenticated attacker with at least read-only (Device Monitor) privileges and access to the management CLI to create, truncate, or overwrite arbitrary files and modify kernel parameters with root privileges by submitting a specially crafted command. Written content is limited to numeric values.
-
CVE-2026-90465
A missing authentication vulnerability in the FireCluster Sync processing allows an attacker positioned on the cluster interconnect, such as a compromised cluster peer or an on-path network attacker, to invoke privileged firewall management actions as root by sending a specially crafted request.
-
CVE-2026-113881
A stack-based buffer overflow vulnerability in Fireware OS's VPN Network Access Enforcement process allows an authenticated mobile VPN user to create a denial of service condition and potentially execute arbitrary code as an unprivileged process by sending a specially crafted request.
-
CVE-2026-115495
Cleartext Transmission of Sensitive Information vulnerability in the WatchGuard Mobile VPN with SSL client for Windows allows a local attacker who can capture loopback traffic to obtain the user’s VPN username and password.
-
CVE-2026-111107
A NULL pointer dereference vulnerability in WatchGuard Fireware OS’s management interface allows a remote, unauthenticated attacker with network access to the management interface to crash the management service by sending a specially crafted login request. Repeated exploitation terminates all active administrator sessions and in-progress management operations and can prevent management of the device. Traffic processing is not affected.
-
CVE-2026-104381
A missing authentication vulnerability in Fireware OS's FireCluster state synchronization feature allows an unauthenticated attacker positioned on the cluster synchronization network segment to force premature VPN tunnel termination by sending crafted cluster synchronization traffic.
-
CVE-2026-112362
@fastify/express is a Fastify plugin that runs Express middleware inside Fastify. In versions 4.0.5 through 4.0.8, when Fastify runs with the non-default ignoreDuplicateSlashes option enabled, the plugin matches path-scoped Express middleware against a URL whose duplicate-slash normalization has also collapsed the separator after an absolute-form request target's scheme, so Fastify's router resolves the request to the scoped path and runs the handler while the Express layer no longer sees that path. As a result, a request using an absolute-form target can reach a handler on a scoped route such as an admin path while the middleware for authentication, authorization, or rate limiting is skipped. An unauthenticated attacker needs only the non-default ignoreDuplicateSlashes option to be enabled. The issue is fixed in @fastify/express 4.0.9, and users should upgrade to 4.0.9 or later. As a workaround, enforce authentication in a Fastify hook such as preHandler that runs after the router resolves the request, or leave ignoreDuplicateSlashes at its default.
-
CVE-2026-106174
A improper locking vulnerability in Fortinet FortiOS 8.0.0, FortiOS 7.6.4 through 7.6.6 may allow an unauthenticated attacker with network access to the device to cause a denial of service of the HTTPS management interface via crafted HTTP requests.
-
CVE-2026-116744
ntop nDPI through 6.0 contains an out-of-bounds read vulnerability in dissect_softether_host_fqdn() in softether.c that compares host_name using the consumed byte count instead of data length. Remote attackers can send crafted short UDP datagrams on already-classified SoftEther flows, causing strncmp to read beyond the packet payload buffer.
-
CVE-2026-116506
A vulnerability was determined in TOTOLINK A950RG 4.1.2cu.5268_B20221104. Affected is the function apmib_set of the file firewall.so. This manipulation causes command injection. The attack may be initiated remotely. The exploit has been publicly disclosed and may be utilized.
-
CVE-2026-116505
A vulnerability was found in TOTOLINK A950RG 4.1.2cu.5268_B20221104. This impacts the function getDeviceInfo of the file /var/lib/misc/udhcpd.leases of the component device-information Handler. The manipulation of the argument MAC address results in command injection. The attack can be launched remotely. The exploit has been made public and could be used.
-
CVE-2026-72756
Routinator exits when an rsync URI for a file obtained over RRDP contains a path that cannot be stored on disk, such as too long file names, and folder names that overlap with existing file names.
-
CVE-2026-72758
When parsing an AS range in Routinator, if the maximum value of the range is smaller than the minimum value of the range, Routinator will never reach the maximum value and run out of memory.
-
CVE-2026-72754
When Routinator encounters a CRL with many entries, it may hang or run out of memory. If Routinator encounters a CRL file with the wrong encoding, it may exit.
-
CVE-2026-72755
Routinator stores a newly-retrieved TA certificate via HTTPS in cache without validation, potentially overwriting a known good TA certificate even if validation fails.
-
CVE-2026-72753
When Routinator encounters an RRDP notification file with gaps in the delta entries, it is still accepted and parsed, potentially leading to missing data. If it encounters too many delta entries it may run out of memory.
-
CVE-2026-116543
Open5GS 1.3.0 through 2.8.0 contains a heap out-of-bounds write vulnerability in parse_multipart() that allows unauthenticated attackers to corrupt memory by supplying an empty multipart boundary. Attackers can send a single crafted multipart/related request to the SBI interface of any network function, overflowing the lookbehind buffer and crashing it.
-
CVE-2026-99088
In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: validate transport header presence in set_ipv6_addr When executing IPv6 address rewrite actions on IPv6 fragments, set_ipv6_addr() calls update_ipv6_checksum(). If parse_ipv6hdr() processes a non-first IPv6 fragment, it sets key->ip.proto to NEXTHDR_FRAGMENT and returns early without calling skb_set_transport_header(). update_ipv6_checksum() unconditionally evaluates skb_transport_offset() on entry before checking l4_proto. Because skb->transport_header is uninitialized, this triggers a warning under CONFIG_DEBUG_NET=y although it is completely harmless. Fix this by returning early in update_ipv6_checksum() if l4_proto is NEXTHDR_FRAGMENT. This avoids reading the uninitialized transport offset for fragments while preserving the debug warning for any other protocol where the transport header is unexpectedly missing. See the syzbot trace: !skb_transport_header_was_set(skb) WARNING: ./include/linux/skbuff.h:3075 at skb_transport_header include/linux/skbuff.h:3075 [inline], CPU#1: syz-executor463/5635 WARNING: ./include/linux/skbuff.h:3075 at skb_transport_offset include/linux/skbuff.h:3250 [inline], CPU#1: syz-executor463/5635 WARNING: ./include/linux/skbuff.h:3075 at update_ipv6_checksum net/openvswitch/actions.c:361 [inline], CPU#1: syz-executor463/5635 WARNING: ./include/linux/skbuff.h:3075 at set_ipv6_addr+0x462/0x660 net/openvswitch/actions.c:399, CPU#1: syz-executor463/5635 [...] RIP: 0010:skb_transport_header include/linux/skbuff.h:3075 [inline] RIP: 0010:skb_transport_offset include/linux/skbuff.h:3250 [inline] RIP: 0010:update_ipv6_checksum net/openvswitch/actions.c:361 [inline] RIP: 0010:set_ipv6_addr+0x462/0x660 net/openvswitch/actions.c:399 [...] Call Trace: <TASK> set_ipv6 net/openvswitch/actions.c:531 [inline] do_execute_actions+0x557e/0x8600 net/openvswitch/actions.c:1366 ovs_execute_actions+0xde/0x520 net/openvswitch/actions.c:1592 ovs_packet_cmd_execute+0xb4f/0xf10 net/openvswitch/datapath.c:705 genl_family_rcv_msg_doit+0x233/0x340 net/netlink/genetlink.c:1114 genl_rcv_msg+0x614/0x7a0 net/netlink/genetlink.c:1209 netlink_rcv_skb+0x226/0x4a0 net/netlink/af_netlink.c:2572 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1218 netlink_unicast+0x7bd/0x940 net/netlink/af_netlink.c:1361 netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1916 sock_sendmsg_nosec+0x14e/0x190 net/socket.c:800
-
CVE-2026-107656
An authentication bypass using an alternate path or channel vulnerability in Fortinet FortiSandbox 5.0.0 through 5.0.6, FortiSandbox 4.4.0 through 4.4.9, FortiSandbox 4.2 all versions, FortiSandbox PaaS 5.0.0 through 5.0.6, FortiSandbox PaaS 4.4 all versions, FortiSandbox PaaS 4.2 all versions may allow attacker to execute unauthorized code or commands via crafted HTTP requests
-
CVE-2026-116237
A vulnerability was found in Oray Pugongying X5 Pro 7.6.1. This affects an unknown part of the component Dnsmasq. Performing a manipulation results in crlf injection. Remote exploitation of the attack is possible. The exploit has been made public and could be used. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-116235
A flaw has been found in Oray Pugongying X5 Pro 7.6.1. Affected by this vulnerability is an unknown functionality of the component L2TP Authentication. This manipulation of the argument Username causes crlf injection. The attack may be initiated remotely. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-116236
A vulnerability has been found in Oray Pugongying X5 Pro 7.6.1. Affected by this issue is the function plugin_init of the file /tmp/upload_files of the component PPPoE WAN Setting Handler. Such manipulation of the argument pppd_options leads to unrestricted upload. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-115425
Multiple cross site scripting (XSS) vulnerabilities affect OPNsense firewall vesrion 26.7.1_1 and earlier allows low privileged attacker to execute Javascript in the context of another user visiting a specific page or clicking on a specifically crafted link.
-
CVE-2026-116233
A security vulnerability has been detected in Oray Pugongying X5 Pro 7.6.1. This impacts an unknown function of the component Dnsmasq. The manipulation of the argument rent_time leads to crlf injection. The attack can be initiated remotely. The exploit has been disclosed publicly and may be used. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-116234
A vulnerability was detected in Oray Pugongying X5 Pro 7.6.1. Affected is an unknown function of the file /etc/ipsec.conf of the component IPsec Policy Handler. The manipulation of the argument secproto results in crlf injection. The attack can be launched remotely. The exploit is now public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-116184
OpenRemote before 1.31.0 contains an authorization bypass vulnerability that allows realm admins to impersonate gateways in other realms because GatewayService only checks the gateway ID, not the realm. Attackers with WRITE:ADMIN in one realm can create a service user named after another realm's gateway ID to overwrite its descendant assets and open SSH tunnels into its local network.
-
CVE-2026-116185
OpenRemote core before 1.31.0 contains an authorization bypass vulnerability that allows authenticated users to read other realms' gateway tunnel information via getGatewayActiveTunnelInfos. Attackers can request the gateway tunnel endpoint with their own realm and a victim gateway ID to disclose internal target hosts, ports, and routing data.
-
CVE-2026-79977
The WireGuard VPN service in subsys/net/lib/wireguard/wg.c updated the peer endpoint from a message it could not authenticate. In handle_transport_data(), when the 32-bit receiver index of an incoming transport-data message matched no session, the code both scheduled a new handshake and copied the datagram's source address into peer->endpoint with memcpy(&peer->endpoint, peer_addr, sizeof(peer->endpoint)). Because the receiver index is unknown, there is no key with which such a message could be verified, so the address written into peer->endpoint is entirely attacker-supplied. Every other endpoint update in the implementation happens only after authentication — after the Noise handshake in handle_handshake_init(), or after AEAD decryption plus the anti-replay check in wg_process_data_message(). The WireGuard listener is registered with net_udp_register() using no remote address or port filter and defaults to UDP port 51820 (CONFIG_WIREGUARD_PORT), and wg_ctrl_recv() resolves the peer by interface rather than by any cryptographic identity. Any host able to send a UDP datagram to that port can therefore reach the defect off-path, with no need to observe legitimate traffic: a 16-byte datagram carrying the transport-data type, zeroed reserved bytes and an arbitrary receiver index is sufficient. The vulnerable branch runs whenever the peer has neither a valid handshake nor a current keypair — the state at boot and after a session expires. A single spoofed datagram redirects peer->endpoint to an address of the attacker's choosing, and all subsequent handshake initiations, keepalives and encrypted data packets are sent there. The legitimate peer never receives the initiations and so never re-authenticates, and nothing resets the endpoint afterwards, leaving the tunnel persistently unusable on devices whose peer does not initiate handshakes itself. The attacker can also relay the redirected initiations to the real peer to place itself in the path of the tunnel, observing ciphertext and traffic metadata and selectively dropping packets. WireGuard's end-to-end cryptography still prevents decryption or forgery of tunnel content, so the impact is loss of availability plus limited confidentiality, not key compromise. The fix removes the endpoint learning from this path entirely: the stale-session recovery is kept, but the handshake is sent only to an endpoint learnt from an authenticated message, falling back to the configured cfg_endpoint, and the message is dropped when neither is known. CONFIG_WIREGUARD is marked experimental and is not enabled by default.
-
CVE-2026-79980
The DHCPv4 client in subsys/net/lib/dhcpv4/dhcpv4.c maintained its transaction identifier (iface->config.dhcpv4.xid) as a counter rather than as a per-transaction random value. It was seeded once with sys_rand32_get() in dhcpv4_start_internal(), incremented by one in dhcpv4_send_discover() and dhcpv4_send_decline(), and never changed by dhcpv4_send_request() — so every RENEWING and REBINDING exchange reused, unchanged, the identifier that had already appeared on the wire in the broadcast DHCPDISCOVER at boot, and where the identifier did move it moved predictably by one. RFC 2131 4.1 requires a single identifier per transaction, chosen so that clients are unlikely to collide. This identifier is the client's only unpredictable reply-validation token. net_dhcpv4_input() accepts a BOOTP reply on op, a matching xid, and a matching chaddr (the interface MAC, which is public); the UDP callback is registered with a wildcard remote address and port, and no server-identifier or source-address check is applied. An attacker who learns one identifier — for example any host on the same segment that sees the broadcast DHCPDISCOVER, or a DHCP server or relay on a network the device previously joined — therefore retains a valid token for the device's whole uptime, and can predict the identifiers of later exchanges, without having to observe the unicast renew traffic or race the legitimate server. A forged reply that passes those checks has effect regardless of client state, because dhcpv4_parse_options() applies its side effects before the state machine gate in dhcpv4_handle_reply(): the router option calls net_if_ipv4_set_gw() and the DNS option calls dns_resolve_reconfigure(). A single accepted datagram can thus repoint the device's default gateway and resolvers at attacker-controlled addresses, redirecting its traffic; during RENEWING or REBINDING a forged DHCPACK re-binds the lease with attacker-chosen parameters and a forged DHCPNAK removes the address and restarts configuration. The fix draws a fresh sys_rand32_get() value at each point where a transaction begins — entering SELECTING, RENEWING and REBINDING, and at the INIT/INIT-REBOOT entry taken when an interface with a lease goes down — while REQUESTING and DECLINE keep the identifier of the exchange they belong to, as RFC 2131 requires. As a side effect the client also no longer discards a slow server's offer after retransmitting a discover, and the initial-discover backoff now draws its own randomness instead of deriving it from the identifier.
-
CVE-2026-115863
ConnMan through 2.0 has a stack-based buffer overflow via a DHCPv6 Reply message. This occurs in get_domains in gdhcp/client.c. It copies a fixed NS_MAXDNAME (1025) bytes from a DHCPv6 DOMAIN_LIST (option 24) value into a 1026-byte stack buffer dns_name regardless of the actual option length, then walks DNS labels with an unbounded "c += jump + 1" loop. A crafted DHCPv6 REPLY with a DOMAIN_LIST option of >= 1025 non-zero bytes makes the label walk leave the buffer and read/write '.' past its end in attacker-chosen strides. An on-link attacker can trigger this without authentication via a forged Router Advertisement (O=1) and a forged DHCPv6 REPLY matching xid/CLIENTID with a long DOMAIN_LIST. The impact is unauthenticated on-link crash of connmand (runs as root). This was introduced in bb06c47.
-
CVE-2026-52356
An OS command injection vulnerability in the /htdocs/web/diagnostic.php endpoint of D-Link DAP1160L A1_FW101WWb04 allows attackers to execute arbitrary commands via injecting arbitrary shell metacharacters.
-
CVE-2026-53918
odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. Prior to version 25.12, odhcpd's DHCPv6 IA handler keeps a per-message `first` lease pointer so multiple IA options in one message reuse the same Reconfigure authentication key. A DHCPv6 REQUEST from an adjacent-network client can make the first IA set `first`, then make a later same-IAID IA fail the on-link check and free that same lease, leaving `first` dangling. A following IA in the same packet allocates a new lease and copies `first->key`, producing a 16-byte heap-use-after-free read. ASan confirms the UAF; native tracing shows the packet shape can deterministically reclaim the freed lease as the destination allocation, producing a zeroed Reconfigure key copy. The validated impact is unauthenticated adjacent-network denial of service and DHCPv6 Reconfigure/ForceRenew key confusion. Arbitrary PC control is not proven for this UAF alone. This issue has been patched in version 25.12.
-
CVE-2026-53920
odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. From version 17.01.0 to before version 25.12.3, odhcpd's DHCPv6 IA parser accepts an IA_NA or IA_PD option whose body is shorter than struct dhcpv6_ia_hdr, casts the option header to that full structure, and reads ia->iaid before proving that the IA body contains the IAID field. If an unauthenticated network-adjacent client places a zero-length or otherwise short IA option at the end of odhcpd's 8192-byte receive stack buffer, the IAID read crosses from data_buf into adjacent stack memory. The disclosed bytes are then reflected in the DHCPv6 reply IAID; prior ARM validation showed data_buf[8192:8196] disclosing the saved stack canary, and wider stack scans can leak ASLR-useful stack/process contents. This issue has been patched in version 25.12.3.
-
CVE-2026-53921
odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. Prior to version 25.12, odhcpd's DHCPv6 IA response handler writes past the end of a fixed 512-byte stack buffer (pdbuf) when a single DHCPv6 REQUEST carries enough IA options to nearly exhaust the reply space. Two independent overflow sites exist in the same call chain, both reachable from the network via a single unauthenticated UDP packet. odhcpd runs as root on OpenWrt; embedded targets often lack stack canaries and ASLR, making code execution realistic. This issue has been patched in version 25.12.
-
CVE-2026-55606
odhcpd is the DHCPv6, DHCPv4, and router-advertisement server used by OpenWrt. In versions 25.12 and prior, odhcpd's DHCPv6 self-loop detection at dhcpv6.c:720 uses a network-byte-order DUID length value directly as the memcmp() size parameter. On little-endian hosts, this causes memcmp() to read far beyond the stack buffer — a single unauthenticated DHCPv6 packet triggers a 2560-byte overread from a 128-byte buffer. At time of publication, there are no publicly available patches.
-
CVE-2026-99081
In the Linux kernel, the following vulnerability has been resolved: bnxt_en: fix DMA mapping length for padded small packets Stefan Fleischmann reported Intel IOMMU DMA Read faults on BCM57412 NetXtreme-E NICs when transmitting packets on VLAN/macvlan interfaces: DMAR: [DMA Read NO_PASID] Request device [18:00.0] fault addr 0xfc499000 [fault reason 0x06] PTE Read access is not set bnxt_en 0000:18:00.0 eno1np0: Abandoning msg {0xb4 0x41a} len: 0 due to firmware status: 0x2000001 ... NETDEV WATCHDOG: eno1np0 (bnxt_en): transmit queue 0 timed out The fault address (0xfc499000) is on an exact 4KB page boundary, pointing to a DMA read buffer overrun. In bnxt_start_xmit(), packets smaller than BNXT_MIN_PKT_SIZE (52 bytes), such as 42-byte untagged ARP frames, are padded: if (length < BNXT_MIN_PKT_SIZE) { pad = BNXT_MIN_PKT_SIZE - length; if (skb_pad(skb, pad)) goto tx_kick_pending; length = BNXT_MIN_PKT_SIZE; } mapping = dma_map_single(&pdev->dev, skb->data, len, DMA_TO_DEVICE); ... dma_unmap_len_set(tx_buf, len, len); However, 'len' was initialized earlier to skb_headlen(skb) (e.g. 42 bytes) and is left unadjusted after padding. Consequently, dma_map_single() and dma_unmap_len_set() map and track only 42 bytes. Later, the hardware TX buffer descriptor is programmed with the padded length: txbd->tx_bd_len_flags_type = cpu_to_le32(((len + pad) << TX_BD_LEN_SHIFT) | flags | TX_BD_FLAGS_PACKET_END); The NIC DMA engine is thus instructed to read 52 bytes from a region where only 42 bytes were DMA-mapped. If skb->data ends near the boundary of a 4KB page (within 'pad' bytes of the next page), the hardware DMA read overruns into the unmapped adjacent page, triggering an IOMMU fault. This issue was exposed after commit 447cbe95ebb9 ("vlan: fix skb_under_panic and races when toggling HW VLAN offload") because reserving extra VLAN headroom rounded LL_RESERVED_SPACE from 48 up to 64 bytes, shifting skb->data offsets and potentially causing small frames to land right against page boundaries. Fix this by using skb_put_padto(skb, BNXT_MIN_PKT_SIZE) in bnxt_start_xmit(), before skb_shinfo(skb)->nr_frags is sampled, because padding might linearize the skb. This ensures skb->len and skb_headlen(skb) reflect the padded size so that dma_map_single() maps the full buffer and the descriptor length is consistent. This also removes the temporary 'pad' variable and masking logic. The padding is done after the SW USO branch, otherwise bnxt_sw_udp_gso_xmit() would account the padding as UDP payload and send it in extra segments. Note that SW USO segments are still not padded: with IPv4, a segment carrying less than 10 bytes of UDP payload (small gso_size, or a short last segment) is sent as a frame shorter than BNXT_MIN_PKT_SIZE. This is a separate issue, left for a followup patch.
-
CVE-2026-99025
In the Linux kernel, the following vulnerability has been resolved: openvswitch: fix soft lockup in the netlink flow dump A production compute node carrying a few thousand datapath flows hit a soft lockup inside a single netlink flow dump and panicked. ovs_flow_cmd_dump() calls ovs_flow_stats_get() for every flow it emits, and that releases stats->lock with spin_unlock_bh() once per CPU that has touched the flow. Every release is a local_bh_enable(), and each one runs the pending softirq backlog in the dumping thread's own context. The skb bounds the flows one callback emits, but not the softirq work it absorbs. On a CPU that carries the box's packet load the backlog refills as fast as it drains, so the dumping thread becomes that CPU's softirq engine. It never sleeps and it has no reschedule point, so under voluntary preemption nothing can take the CPU away from it: neither the ksoftirqd the kernel woke to take the work over, nor the stopper thread the softlockup detector dispatches to refresh its timestamp. Hold BH off across the whole callback instead, the way ctnetlink_dump_table() does, so the nested spin_unlock_bh() stop draining softirqs. The loop already runs under rcu_read_lock() and cannot sleep. What it gives up is preemption under CONFIG_PREEMPT, since a BH-off region is not preemptible outside PREEMPT_RT. The region stays short: the skb caps the flows one callback emits, and empty buckets cost no skb space but are each visited once per dump, as the cursor only moves forward. The table grows on insert and shrinks only on flush, so the walk is bounded by the largest flow count the datapath has held. The softirq backlog the callback used to absorb has no bound at all.
-
CVE-2026-98968
In the Linux kernel, the following vulnerability has been resolved: amt: send the relay's General Query directly from the receive path An skb queued in a qdisc can outlive the tunnel it references through a raw pointer in skb->cb. For example, with igmp_qrv set to 1 on the relay a tunnel lives for 135s, so a netem delay of 180s on the amt device outlives it; when the tunnel expires and is freed, the subsequent dequeue triggers a use-after-free in amt_dev_xmit(). BUG: KASAN: slab-use-after-free in amt_dev_xmit+0x2763/0x2e20 Call Trace: amt_dev_xmit+0x2763/0x2e20 [drivers/net/amt.c:1262] dev_hard_start_xmit+0x22f/0x620 sch_direct_xmit+0x12e/0xac0 netem_dequeue+0x333/0xc50 net_tx_action+0x35c/0xa60 amt_send_igmp_gq() and amt_send_mld_gq() are only called from amt_request_handler(), inside the rcu_read_lock_bh() section of amt_rcv(). amt_request_handler() already has the tunnel the query is for: it found or created it inside that section. Queuing the query with dev_queue_xmit() only leads back into amt_dev_xmit(), which strips the Ethernet header and calls amt_send_membership_query() for that tunnel. Make that call directly from the two senders instead, the same way amt_send_advertisement() transmits from the receive path. The query never waits in a qdisc, the tunnel is only dereferenced inside the RCU section that found or created it, and nothing is stored in skb->cb, so no lookup or refcount is needed. Remove the query branch of amt_dev_xmit(), amt_skb_cb() and struct amt_skb_cb, which have no users left. Behaviour changes: - The relay's own General Queries no longer pass through the amt device's egress path: its qdisc, tc egress (clsact/tcx), the netfilter egress hook and packet taps. They are still visible as UDP on the underlay. - A query that is sent successfully is no longer counted as tx_dropped. The old query branch left through the unlock label, which counted every sent query as dropped. - A query that reaches amt_dev_xmit() on a relay from elsewhere, such as a userspace querier, is now dropped at the IGMP/MLD type switch. Before, it trusted whatever skb->cb held, and a NULL tunnel hit the WARN_ON(1).
-
CVE-2026-98906
In the Linux kernel, the following vulnerability has been resolved: net: lan966x: restore RX state on reload failure lan966x_fdma_reload() backs up rx->page_pool and rx->fdma before reallocating the RX resources for the new MTU. If the allocation fails, the restore path puts these fields back before restarting RX. However, the reload path also updates rx->page_order and rx->max_mtu before calling lan966x_fdma_rx_alloc(). These fields are not restored on failure, so RX can be restarted with the old pages, old FDMA state and old page pool, but with the page geometry from the failed new MTU. This can make the XDP path advertise a frame size derived from the new page_order while the actual RX pages still come from the old allocation. For example, after a failed reload to a jumbo MTU, xdp_init_buff() may be called with a frame size larger than the restored RX pages. lan966x_fdma_rx_alloc_page_pool() also registers the newly allocated page pool with each port's XDP RXQ before fdma_alloc_coherent() is called. If fdma_alloc_coherent() fails, the new page pool is destroyed, but the rollback path does not restore the per-port XDP RXQ mem model registration either. Save and restore rx->page_order and rx->max_mtu, and restore the old page pool registration for each port's XDP RXQ before RX is started again. This keeps the restored RX state consistent after a failed reload.
The newest published CVE records from CVE.org and NVD, refreshed every few minutes, with severity, exploit odds and fix status.