CVE-20XX-?
agent?

Just published.

The newest CVEs, straight from CVE.org and NVD.

2,495 CVEs · updated 2026-11-20 19:24 UTC

Reset all
  1. CVE-2026-99062

    In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: account only unread bytes in read_skb() After a partial stream receive, rx_bytes tracks the unread suffix while buf_used and peer credit still cover the whole packet. virtio_transport_read_skb() dequeues that packet but passes pkt_len for both counters, underflowing rx_bytes. On a connected CID_LOCAL stream with an SK_SKB verdict, a 40-byte read from a 100-byte packet made SIOCINQ report -40, an empty recv return ELOOP, and poll report the empty socket readable. After verdict detach, receiving 40 bytes wrapped the counter to zero and hid those queued bytes until one more byte arrived. The fixed run kept the counter balanced and exposed all queued data immediately. This was found during an LLM-assisted manual source audit of VSOCK receive accounting while re-evaluating virtio_transport_read_skb() after CVE-2024-50169. Subtract only skb->len minus the VSOCK offset from rx_bytes. Retain the full packet length for buf_used and peer credit.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  2. CVE-2026-99064

    In the Linux kernel, the following vulnerability has been resolved: cipso: adjust cached option offsets when removing CIPSO cipso_v4_skbuff_delattr() removes the CIPSO bytes but does not adjust cached offsets for options that follow them. For example, with a valid 10-byte CIPSO option followed by a seven-byte RR option, parsing records rr at offset 30. Removing CIPSO moves RR to offset 20, while the cached offset remains 30. Consumers such as ip_forward_options() and __ip_options_echo() then access the wrong bytes; the latter may interpret packet data as the option length and copy it into fixed-size option storage. Mirror cipso_v4_delopt() and subtract cipso_len from the srr, rr, ts and router_alert offsets when they follow CIPSO. cipso_len is the distance the first memmove() shifts those options. The later header move and network-header reset relocate the bytes and their offset base together.

    Other OS & kernel

    8.1 HIGH 0.5% exploit odds No fix listed
  3. CVE-2026-99065

    In the Linux kernel, the following vulnerability has been resolved: cgroup/cpuset: Handle cpu hotplug race in guarantee_active_cpus() With commit 2125c0034c5d ("cgroup/cpuset: Make cpuset hotplug processing synchronous"), the cpuset hotplug operation becomes synchronous. That commit also removes the code that handles race between cpuset_hotplug_work and cpu hotplug notifier with the assumption that race is now gone. Later commit 7a0aabd9ce69 ("cgroup/cpuset: Always use cpu_active_mask") updates the cpuset code to always use cpu_active_mask instead of cpu_online_mask in some places including guarantee_online_cpus() which is renamed to guarantee_active_cpus() in that commit. In the case of CPU offline operation, cpu_active_mask is updated first in sched_cpu_deactivate() to remove the offline CPU before cpuset_handle_hotplug() is called to update the effective_cpus of the affected cpusets. The cpu_online_mask is updated after that near the end of the offline operation to remove the offline CPU. As a result, the race comes back and the top cpuset may not have any active CPU leading to NULL pointer dereference during the race window when guarantee_active_cpus() is called after cpu_active_mask is updated to remove the CPU to be torn down but before cpuset_handle_hotplug() is able to properly update the effective_cpus of the top cpuset. Fix this by adding back the NULL cs check to avoid this problem.

    Other OS & kernel

    unscored 0.2% exploit odds Fix listed
  4. CVE-2026-99067

    In the Linux kernel, the following vulnerability has been resolved: btrfs: scrub: fix local_root reference leak in scrub_print_warning_inode() When paths_from_inode() fails, scrub_print_warning_inode() jumps to err without dropping the reference taken by btrfs_get_fs_root(), leaking a reference to the root every time path resolution fails while printing scrub warnings. Every other error and success path of the function drops the reference. Drop the reference on the paths_from_inode() failure path too.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  5. CVE-2026-99069

    In the Linux kernel, the following vulnerability has been resolved: Input: ati_remote2 - fix type confusion in device attribute handlers Previously, the channel_mask and mode_mask attributes were registered on the parent usb_device via sysfs_create_group(). When commit b20d6bf8014b ("Input: ati-remote2 - use driver core to instantiate device attributes") converted the driver to let the driver core manage them via dev_groups in struct usb_driver, the attributes moved to the bound usb_interface devices, but the show and store callbacks were not updated accordingly. As a result, the callbacks still invoked to_usb_device() on a device pointer belonging to a struct usb_interface, producing an invalid usb_device pointer. Use to_usb_interface() directly in the attribute handlers to obtain the interface and its driver data.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  6. CVE-2026-99070

    In the Linux kernel, the following vulnerability has been resolved: ipv6: do not warn on route notification size race fib6_info_hw_flags_set() sizes the skb with rt6_nlmsg_size() and later fills it with rt6_fill_node(). With nexthop compatibility mode enabled, a concurrent replacement can grow the group between these independent snapshots. rt6_fill_node() can then legitimately return -EMSGSIZE, so the warning does not prove a sizing bug. Remove the warning. The existing error path still frees the skb and reports the error to listeners.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  7. CVE-2026-99055

    In the Linux kernel, the following vulnerability has been resolved: tcp: reject net_iov in zerocopy receive mapping hints After copying a readable prefix, receive_fallback_to_copy() asks tcp_zerocopy_set_hint_for_skb() where page mapping can resume. If the next skb is unreadable, find_next_mappable_frag() passes its net_iov fragment to can_map_frag(). skb_frag_page() returns NULL for a net_iov, but can_map_frag() dereferences it in PageCompound(). A v7.2 KASAN run on a connected TCP socket with 64 readable bytes followed by a 4096-byte NET_IOV_DMABUF fragment reported: BUG: KASAN: null-ptr-deref in can_map_frag tcp_zerocopy_receive -> can_map_frag Kernel panic - not syncing: KASAN: panic_on_warn set The diagnostic inserted the net_iov directly because the test host has no devmem-capable NIC. Hardware end-to-end reachability remains untested and requires CONFIG_NET_DEVMEM plus a supported DMA-buf-bound RX queue. Reject all net_iov fragments before skb_frag_page(). This covers both DMABUF and IOURING net_iov types while leaving page-backed checks unchanged. With the guard, the same queue copied the readable prefix, returned a 4096-byte skip hint, and completed without a fault.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  8. CVE-2026-99058

    In the Linux kernel, the following vulnerability has been resolved: workqueue: Fix NULL current_pwq deref in chained work check current_wq_worker() only tells us that %current is a kworker. It does not guarantee that the worker is currently executing a work item, as worker->current_pwq is populated only while process_one_work() is running the work function. is_chained_work() can be reached while queueing on a draining or destroying workqueue. If a kworker outside work-item execution reaches that path, current_wq_worker() returns a worker but worker->current_pwq is NULL, and the chained-work test can fault before it emits the intended warning. Guard the chained-work test with worker->current_pwq. A kworker without current_pwq is not executing work on the target workqueue, so the helper should return false and let the draining/destroying warning fire.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  9. CVE-2026-99059

    In the Linux kernel, the following vulnerability has been resolved: wireguard: noise: reject response consumption after intermediate initiation Two threads begin processing the identical response message, received twice. The first thread, A, runs. While it's running, the second one, B, gets partway through, and during that slow calculation, or even while blocking on down_write(), A completes and then also a handshake initiation that's already been queued up runs in thread C, which itself takes that same down_write(). The handshake initiation creation succeeds, and sets the state back to waiting-for-response, and calls up_write(), at which point thread B resumes, because either its finished its calculations or was finally allowed to acquire down_write(). Thread B then copies the state back to the peer, and begins a new session, using that state, which is the same session as the one made in thread A. Thread A Thread B Thread C down_read() sA = handshake->state memcpy(cA, handshake->crypto) up_read() if (sA != 1) goto fail slow_crypto(cA) down_read() sB = handshake->state memcpy(cB, handshake->crypto) up_read() if (sB != 1) goto fail slow_crypto(cB) down_write() if (sA != handshake->state) goto fail memcpy(handshake->crypto, cA) handshake->state = 2 up_write() down_write() if (handshake->state != 2) goto fail derive_session(handshake->crypto) up_write() down_write() slow_crypto(handshake->crypto) handshake->state = 1 up_write() down_write() if (sB != handshake->state) goto fail memcpy(handshake->crypto, cB) handshake->state = 2 up_write() down_write() if (handshake->state != 2) goto fail derive_session(handshake->crypto) up_write() This seems basically impossible to hit in a meaningful way in practice, but ensure that it absolutely cannot happen by comparing the ephemeral private key that's on the stack with the latest one that the peer's handshake state has.

    Other OS & kernel

    7.7 HIGH 0.5% exploit odds No fix listed
  10. CVE-2026-99060

    In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7603: initialize global station WCID mt7603 uses a driver-private global station WCID for frames that have neither a station nor a vif, including frames injected through a monitor interface. Unlike the core global WCID initialized by mt76_register_device(), this WCID is published without ever being passed to mt76_wcid_init(). Since commit 0335c034e726 ("wifi: mt76: fix race condition related to checking tx queue fill status"), mt76_tx() queues every such frame on the WCID's tx_pending or tx_offchannel queue and links its tx_list. The first injected frame therefore reaches __skb_queue_tail() with an uninitialized sk_buff_head and dereferences a NULL prev pointer. Initialize the WCID before publishing it. The fix was tested on an MT7603 PCIe device. Three wildcard probe requests were injected through a monitor interface. The hardware queue head and tail advanced from 0 to 3 and a second radio captured the third request over the air. No oops or reset occurred. After restoring AP mode, a 150 MB transfer also completed without a reset.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  11. CVE-2026-99048

    In the Linux kernel, the following vulnerability has been resolved: gve: fix napi_disable deadlock when attempting to disable XSK pools When disabling XSK pools, GVE calls the unlocked versions of napi_disable and napi_enable. However, the netdev lock has already been acquired before ndo_bpf is called because GVE supports queue management ops. Calling the unlocked versions of napi_disable/enable results in a deadlock when attempting to disable XSK pools, as the thread attempts to re-acquire a lock it already holds. Update the NAPI calls to use the locked versions. This issue was found in production.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  12. CVE-2026-99049

    In the Linux kernel, the following vulnerability has been resolved: gpio: xilinx: fix runtime PM leak on request error path pm_runtime_get_sync() leaves the usage counter incremented even when it fails, and xgpio_request() returns the error without dropping it. gpiolib does not call ->free() when ->request() fails, so xgpio_free(), which holds the only matching pm_runtime_put(), never runs. The reference is leaked and the controller can no longer runtime-suspend, so its clock stays enabled. Switch to pm_runtime_resume_and_get(), which only increments the usage counter on success.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  13. CVE-2026-99052

    In the Linux kernel, the following vulnerability has been resolved: selinux: preserve NATIVE_LABELS on already-initialized sb in set_mnt_opts When an NFSv4 filesystem exported with security_label is mounted a second time, sget_fc() returns the existing superblock and nfs_get_root() calls security_sb_set_mnt_opts() again on it. Since the superblock is already SB_INITIALIZED, selinux_set_mnt_opts() takes an early exit without setting SECURITY_LSM_NATIVE_LABELS in *set_kern_flags. nfs_get_root() then sees kflags without SECURITY_LSM_NATIVE_LABELS set and clears NFS_CAP_SECURITY_LABEL on the shared nfs_server, silently disabling per-file labeling for both the new and the original mount. Commit 3815a245b501 ("security/selinux: fix SECURITY_LSM_NATIVE_LABELS on reused superblock") fixed the same problem in selinux_sb_clone_mnt_opts(). The reused-superblock path for a plain second mount now goes through sb_set_mnt_opts rather than sb_clone_mnt_opts, so it needs the same treatment: on both SE_SBINITIALIZED early exits, set SECURITY_LSM_NATIVE_LABELS in *set_kern_flags when the superblock was already using SECURITY_FS_USE_NATVE.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  14. CVE-2026-99038

    In the Linux kernel, the following vulnerability has been resolved: memstick: rtsx_usb_ms: complete requests after eject instead of dropping them memstick_check() can pass its host->removing check just before rtsx_usb_ms_drv_remove() sets eject/removing. Its next request is then silently dropped: rtsx_usb_ms_request() skips schedule_work() once eject is set, and drv_remove's cancel_work_sync() can also cancel a queued handle_req before it picks the request up. Nobody completes card->mrq_complete. Once memstick core waits for requests without a timeout ("memstick: core: wait for request completion before freeing card"), this hangs removal: memstick_check() never returns and memstick_remove_host() blocks in flush_workqueue(): INFO: task kworker/u10:3:65 blocked for more than 20 seconds. Workqueue: kmemstick memstick_check __wait_for_common memstick_check INFO: task kworker/1:1:33 blocked for more than 20 seconds. Workqueue: usb_hub_wq hub_event __flush_workqueue memstick_remove_host rtsx_usb_ms_drv_remove Never drop a request. rtsx_usb_ms_request() always schedules handle_req, and handle_req fails requests with -ENOMEDIUM once eject is set, without touching the device. drv_remove flushes handle_req instead of cancelling it, and cancels it only after memstick_remove_host(), when no new request can arrive, so it cannot run on a freed host. The host_mutex drain in drv_remove is removed: handle_req always leaves host->req NULL when it finishes, so the drain never had anything to do, and it would now race with handle_req.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  15. CVE-2026-99040

    In the Linux kernel, the following vulnerability has been resolved: KEYS: Fix add_key() race with keyring restriction __key_create_or_update() snapshots keyring->restrict_link before taking the destination keyring's semaphore. keyring_restrict() installs a restriction while holding that semaphore. This allows a writer to observe no restriction, wait for the keyring owner to install a reject-all restriction and return successfully, and then link a key using the stale NULL snapshot. The writer only needs write permission on the destination keyring. Move the restrict_link read after __key_link_lock() and __key_link_begin(). The read and the subsequent restriction check are then serialized with restriction installation by keyring->sem. The race was reproduced on v7.2.8 in 19 executions where restriction installation returned before the link completed. All 19 linked the key despite the reject-all restriction. With this change, 312 executions reached the same ordering and every add_key() call failed with -EPERM. The issue was found by manual concurrency analysis assisted by AI-based analysis and independently verified with a QEMU reproducer and kernel instrumentation.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  16. CVE-2026-99041

    In the Linux kernel, the following vulnerability has been resolved: ip6_gre: remove obsolete ERSPAN PMTU update A tc tunnel_key action can attach a METADATA_IP_TUNNEL dst to an skb, and mirred can redirect it to a native ip6erspan device. The legacy PMTU update in ip6erspan_tunnel_xmit() treats that metadata dst as a route. Since it has no output device, dst_dev(dst)->mtu dereferences NULL. On v7.2 with KASAN, an initial UID/GID 65534 process with CapEff 0 used self-created user and network namespaces to trigger: KASAN: null-ptr-deref RIP: ip6erspan_tunnel_xmit+0x10fc/0x2cc0 Kernel panic - not syncing: Fatal exception in interrupt The update is obsolete. Commit fe1a4ca0a2b7 ("ip6_gre: process toobig in a better way") changed IPv6 GRE Too Big handling to update the underlay route and removed the equivalent block from __gre6_xmit(). ip6_tnl_xmit() then propagates the underlay PMTU to the overlay route. Remove the stale ERSPAN copy and its now-unused dst variable. This eliminates the metadata-dst dereference and keeps ERSPAN aligned with IPv6 GRE PMTU handling.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  17. CVE-2026-99042

    In the Linux kernel, the following vulnerability has been resolved: io_uring/net: populate CONNECT filter fields for 24-byte sockaddr_in6 io_connect_bpf_populate() fills connect.port and connect.v6_addr for AF_INET6 only when addr_len >= sizeof(struct sockaddr_in6), i.e. 28 bytes. The IPv6 connect paths accept SIN6_LEN_RFC2133 (24 bytes), which already holds sin6_port and sin6_addr. io_connect() passes addr_len to the socket layer unchanged. At addr_len 24 the filter sees family AF_INET6 with port and address zero, while the kernel connects to the real destination. A filter that denies an IPv6 port or address is bypassed. Denying connect.port == P rejects [::1]:P with -EACCES at addr_len 28 but connects at addr_len 24. Use SIN6_LEN_RFC2133 as the threshold. sin6_scope_id stays zero when absent. The threshold mismatch was found by an AI coding assistant (Claude Code) comparing this hook against the net/ipv6 length checks on my instructions; it also drafted the reproducer and this patch. I verified the bypass and the fix in a VM on 7.3-rc6 and that 7.2 has the same code.

    Other OS & kernel

    8.4 HIGH 0.2% exploit odds No fix listed
  18. CVE-2026-99043

    In the Linux kernel, the following vulnerability has been resolved: ice: fix metadata_dst refcount handling on representor teardown ice_eswitch_release_repr() uses metadata_dst_free() to release the representor's metadata_dst. metadata_dst_free() directly frees the underlying memory without checking the dst_entry refcount. When ice_eswitch_port_start_xmit() processes a packet, it takes a reference via dst_hold() and attaches the metadata_dst to the skb. If the representor is torn down while packets are still queued on the lower device (e.g. in a qdisc), the metadata_dst is freed while references are still held. Use dst_release() instead, which correctly decrements the refcount and only frees the object when all references are dropped. The dst subsystem already handles metadata_dst cleanup in dst_destroy() when DST_METADATA is set. Other drivers sharing this pattern (nfp, airoha, bnxt) already use dst_release() for their metadata_dst lifecycle.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  19. CVE-2026-99045

    In the Linux kernel, the following vulnerability has been resolved: ibmveth: h_free logical LAN on open-fail after register ibmveth_open() registers the logical LAN, then allocates the RX buffer pools. A pool failure jumps to out_free_buffer_pools without h_free_logical_lan(), so PHYP still owns the buffer-list page when it is unmapped. request_irq() failure already issued the hypercall before taking the same label. Move that h_free to the shared post-register unwind so both paths deregister before the buffer list is unmapped.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  20. CVE-2026-99031

    In the Linux kernel, the following vulnerability has been resolved: net: bridge: avoid recursive multicast port cleanup br_multicast_sg_del_exclude_ports() removes automatically added STAR_EXCL port groups by calling br_multicast_del_pg(). For S,G entries, that deletion calls back into br_multicast_sg_del_exclude_ports(), so a large number of STAR_EXCL ports consumes one kernel stack frame per port and can hit the stack guard page. Keep the complete port-group deletion path for cleanup, but suppress the S,G exclude-port cleanup while that helper is already walking the same entry. Normal deletion callers retain the existing behavior.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  21. CVE-2026-99033

    In the Linux kernel, the following vulnerability has been resolved: net/packet: guard the ll header push in packet_rcv_spkt() packet_rcv_spkt() restores the link layer header with skb_push(skb, skb->data - skb_mac_header(skb)); That subtraction is only meaningful when the device actually has a link layer header. packet_rcv() and tpacket_rcv() both wrap it in dev_has_header(), which is also the predicate the block comment at the top of the file states the restore in terms of; packet_rcv_spkt() does not. commit d549699048b4 ("net/packet: fix packet receive on L3 devices without visible hard header") introduced the helper and changed the two call sites, and this one stayed behind. A device without a visible ll header can leave skb->mac_header at the 0xFFFF sentinel that __alloc_skb() initialises it to. A CAN skb does: init_can_skb() sets pkt_type and ip_summed but does not reset the headers, and commit 9f10374bb024 ("can: remove private CAN skb headroom infrastructure") dropped the skb_reset_*_header() calls that used to be there. skb_mac_header() is then 0xFFFF, the length becomes a large negative number and skb_push() reports it through skb_under_panic() -- from softirq context, so it is a full system panic even with panic_on_oops=0: skbuff: skb_under_panic: text:ffffffff8bd21bc1 len:-65455 put:-65471 head:... data:... tail:0x50 end:0x180 dev:can0 kernel BUG at net/core/skbuff.c:214! RIP: 0010:skb_panic+0x50/0x60 Call Trace: <IRQ> skb_push+0x38/0x40 packet_rcv_spkt+0xe1/0x170 __netif_receive_skb_core.constprop.0+0x7e8/0xd30 ... Kernel panic - not syncing: Fatal exception in interrupt The socket type is reachable: packet_create() accepts SOCK_PACKET alongside SOCK_RAW and SOCK_DGRAM behind the same CAP_NET_RAW check, and neither the socket length nor a capability check keeps it away from a CAN interface. The missing skb_reset_*_header() calls in init_can_skb() are a regression in their own right and are being fixed separately, but a packet socket should not turn a link layer that did not initialise its mac header into a kernel panic. Guard the push the way the other two receive paths do. Tested on v7.3-rc5 under QEMU with a slcan device on a pty, which is the driver RX path: vcan does not reproduce it, because can_send() resets the headers on the way out. One SOCK_PACKET socket bound to can0 and one frame written into the line discipline panics an unpatched kernel with the trace above; the same image with this patch prints no panic and powers off normally. Both kernels are this tree, defconfig plus CONFIG_CAN_SLCAN=y, differing only in this hunk.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  22. CVE-2026-99034

    In the Linux kernel, the following vulnerability has been resolved: mmc: sdhci-sprd: disable runtime PM on remove sdhci_sprd_probe() enables runtime PM, while sdhci_sprd_remove() does not perform the corresponding runtime PM cleanup. The probe failure path disables runtime PM before disabling the clocks, but the normal remove path directly disables clocks that are also managed by the runtime PM callbacks. If the device is runtime suspended, those clocks may already be disabled. Resume the device before removal, disable runtime PM and drop the temporary runtime PM reference before disabling the clocks. This issue was found by manual code inspection.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  23. CVE-2026-99037

    In the Linux kernel, the following vulnerability has been resolved: dm-crypt: reject the lmk IV mode with AEAD ciphers A "capi:" table line that pairs an AEAD cipher with the lmk IV mode, for example "capi:gcm(aes)-lmk" with the integrity:28:aead option, causes an oops when it is loaded. lmk sets tfms_count to 64, but crypt_alloc_tfms_aead only allocates one transform, so crypt_setkey reads past the end of the tfms_aead array and calls crypto_aead_setkey on the values it finds there. lmk exists for compatibility with Loop-AES, which uses CBC, so refuse it with an AEAD cipher rather than allocate 64 AEAD transforms. The check cannot go in crypt_iv_lmk_ctr with the other lmk checks, because the IV constructor runs after crypt_set_key. Note that this is not a security bug because the memory corruption can only be triggered by root.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  24. CVE-2026-99022

    In the Linux kernel, the following vulnerability has been resolved: regulator: ltc3676: don't read the write-only HRST and CLIRQ registers HRST (0x1e) and CLIRQ (0x1f) are write-only command strobes. Writing HRST triggers a hard reset of the chip and writing CLIRQ clears the interrupt; reading them returns nothing useful, and the read itself fires the command. The result is that a plain register dump resets the board: cat /sys/kernel/debug/regmap/2-003c/registers walks every readable register, hits HRST, and the board reboots. Split the callback back in two so HRST and CLIRQ stay writable but are no longer readable. The readable range is left unchanged (LTC3676_BUCK1 ... LTC3676_IRQSTAT).

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  25. CVE-2026-99024

    In the Linux kernel, the following vulnerability has been resolved: optee: register TEE devices only once fully initialized optee_probe() called tee_device_register() on both the client and the supplicant device before the rest of struct optee had been initialized. tee_device_register() calls cdev_device_add(), which does two things at once: it creates /dev/tee0 and /dev/teepriv0, and it links the device into the tee class so that class_find_device() can find it. From that moment on the device is reachable both from user space via tee_open() and from kernel space via tee_client_open_context(). The only gate in teedev_open() is tee_device_get(), which merely checks that teedev->desc is non-NULL, which was already set by tee_device_alloc(). Therefore, there is effectively no gate at all. A context opened in that window can run against a struct optee where - optee->call_queue.mutex is not initialized by optee_cq_init() - optee->supp mutex and completions is not initialized by optee_supp_init() - optee->rpmb_dev_mutex is not initialized yet, - the message argument cache is not initialized by optee_shm_arg_cache_init() - optee->ctx is still NULL Any open session or invoke during this window takes uninitialized mutexes and dereferences a NULL pointer. Fix it by moving both tee_device_register() calls down to the point where all of struct optee is set up. [JW: adding fixes and cc]

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  26. CVE-2026-99026

    In the Linux kernel, the following vulnerability has been resolved: net: team: free skb when broadcast has no txable port bc_transmit() sends the original skb through the last txable port. When no port is txable, it returns false without consuming the skb, but team_xmit() still returns NETDEV_TX_OK. AF_PACKET sends then retain the skb and its socket write-memory charge. A TX-enabled, link-down port keeps the broadcast transmit op installed. Carrier can stay up through a second link-up, TX-disabled port or be forced on by userspace. Free the original skb on the no-port path while leaving the existing drop accounting intact. Discovered by Sashiko during review of previous commit.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  27. CVE-2026-99028

    In the Linux kernel, the following vulnerability has been resolved: net: xilinx: axienet: Free outstanding DMA buffers on dmaengine stop In the dmaengine path the driver pre-submits RX buffers and holds in-flight TX buffers whose SKBs are DMA-mapped by the driver and freed only in the completion callbacks. On ndo_stop() dmaengine_terminate_sync() aborts these descriptors without running their callbacks, and the driver then frees only the ring shells, leaking every SKB still owned by the engine and its DMA mapping on each ifdown. With 128 RX buffers pre-posted per channel, the mapping leak can eventually exhaust a limited IOMMU aperture. Clear the slot's skb in the TX and RX callbacks so a non-NULL skb marks a slot that still owns a live, DMA-mapped buffer, and on stop unmap and free every such buffer. axienet_dma_rx_cb() runs from the DMA tasklet and re-arms the RX ring on each completion, so it can race axienet_stop(): a completion may submit a fresh buffer after dmaengine_terminate_sync() has returned, leaving the channel armed with a buffer the teardown then frees while the engine may still write into it (dma_release_channel() does not stop it either). Add a lock that axienet_dma_rx_cb() holds across the @stopping check and the resubmit, and axienet_stop() holds to set @stopping before terminating. Once @stopping is set no callback can arm a new buffer, and any armed just before is aborted by the terminate, so teardown only frees buffers the engine no longer owns.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  28. CVE-2026-99013

    In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: Reject concurrent BIS listener setup iso_sock_listen() drops the socket lock before calling iso_listen_bis() to preserve the hdev->lock ordering. Two concurrent listen() calls on the same broadcast socket can therefore both observe BT_BOUND. Caller A can attach connA and release the locks, then caller B can acquire them and attach connB before A publishes BT_LISTEN. __iso_chan_add() checks whether connB already has a socket, but not whether the socket already has a connection. The second attachment overwrites iso_pi(sk)->conn, leaking the connA reference and leaving connA->sk intact. Socket teardown follows connB, so later events on connA can cause a stale socket access. Recheck BT_BOUND and require iso_pi(sk)->conn to be NULL after taking both the HCI device and socket locks in iso_listen_bis(). The connection check also covers the interval between attachment and publication of BT_LISTEN. Reject a competing setup with -EBADFD through the existing unlock path before allocating another connection. A recorded KASAN report from an instrumented kernel shows: BUG: KASAN: slab-use-after-free in iso_sock_hold+0x119/0x1f0 Call Trace: iso_sock_hold+0x119/0x1f0 iso_conn_del+0xe4/0x270 hci_disconn_complete_evt+0x351/0x8c0 hci_event_packet+0x71b/0xb20 hci_rx_work+0x293/0x730 Allocated by task 93: sk_prot_alloc+0x113/0x220 sk_alloc+0x2b/0x6d0 bt_sock_alloc+0x29/0x370 iso_sock_alloc.constprop.0+0x19/0x300 iso_sock_create+0x94/0x100 Freed by task 93: kfree+0x121/0x3c0 __sk_destruct+0x42b/0x540 iso_sock_release+0x29d/0x340 __sock_release+0xa1/0x260 sock_close+0x10/0x20

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  29. CVE-2026-99016

    In the Linux kernel, the following vulnerability has been resolved: riscv: futex: untag the user pointer before the atomic access access_ok() checks untagged_addr(uaddr), but arch_futex_atomic_op_inuser() and futex_atomic_cmpxchg_inatomic() hand the raw uaddr to the inline asm amoswap/amoadd/.../lr.w+sc.w through the "+m" (*uaddr) operand. When the tagged address ABI is enabled (CONFIG_RISCV_ISA_SUPM, prctl PR_SET_TAGGED_ADDR_CTRL with PMLEN != 0), those two addresses differ: a user pointer whose top PMLEN bits hold a tag passes access_ok() after untagging, but the atomic is then performed on the still-tagged raw address. Supervisor-mode data accesses are not subject to the U-mode pointer masking (that is governed by menvcfg.PMM, which the kernel does not set), so hardware does not strip the tag for the kernel's own access. With Sv57 and PMLEN=16 the tag bits overlap the canonical-address bits, so a tagged pointer can name a canonical kernel virtual address (e.g. in the linear map) whose untagged form is a valid user address. An unprivileged process can thus make FUTEX_WAKE_OP perform an atomic read-modify-write on an arbitrary kernel address, with the matching FUTEX_OP_CMP_* result serving as a read oracle. get_user()/put_user()/raw_copy_{to,from}_user() already untag the pointer after the access_ok() check; do the same in the futex helpers so the atomic operates on the address that was actually validated.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  30. CVE-2026-99017

    In the Linux kernel, the following vulnerability has been resolved: riscv: errata: select RISCV_ALTERNATIVE_EARLY for THEAD GHOSTWRITE errata_probe_ghostwrite() only marks the CPU as vulnerable when it is called at the RISCV_ALTERNATIVES_EARLY_BOOT stage, and the mitigation in ghostwrite_enable_mitigation() only takes effect if the vulnerable state was recorded before the boot alternatives are patched. The early boot stage is only executed when CONFIG_RISCV_ALTERNATIVE_EARLY is enabled, which currently is only selected by ERRATA_THEAD_MAE. In a kernel built with ERRATA_THEAD_GHOSTWRITE=y but ERRATA_THEAD_MAE=n, the early alternatives never run, so ghostwrite_state is never set to VULNERABLE: ghostwrite_enable_mitigation() returns false, xtheadvector remains enabled, and sysfs reports "Not affected" on a vulnerable T-Head C9xx CPU. Select RISCV_ALTERNATIVE_EARLY from ERRATA_THEAD_GHOSTWRITE so that the vulnerability is detected in the early boot stage and the default mitigation is applied.

    Other OS & kernel

    7.0 HIGH 0.2% exploit odds No fix listed
  31. CVE-2026-99018

    In the Linux kernel, the following vulnerability has been resolved: riscv: entry: gate shadow call stack reload on sstatus.SPP, not tp Under CONFIG_SHADOW_CALL_STACK, handle_exception() reloads the kernel shadow call stack pointer (gp) only when the trap came from userspace. It made that decision with scs_load_current_if_task_changed, which compares the trap-time tp (read back from sscratch into s5) against the current tp: beq \prev, tp, _skip_scs scs_load_current _skip_scs: tp is a user-writable register. A user task that sets tp to the linear-map address of its own task_struct (&current) before trapping makes the comparison succeed (can achieve by brute force with KASLR enable under our test), so the kernel skips scs_load_current and keeps running with the gp that userspace left in place. Under CONFIG_SHADOW_CALL_STACK gp is the shadow call stack pointer and load_global_pointer is a no-op, so the compiler-emitted "sd ra, -8(gp)" / "ld ra, -8(gp)" in every non-leaf function then write to, and return through, an attacker-controlled address -- an unprivileged kernel arbitrary-write and control-flow-hijack primitive. The poisoned gp is saved to task_struct.scs_sp on return, so the reload is skipped on every subsequent entry as well. Decide "came from userspace" from the hardware sstatus.SPP bit (already in s1 at this point) instead of from tp, mirroring the check that ret_from_exception already uses a few instructions later. SPP is written by hardware on trap entry and cannot be forged from U-mode. Legitimate behaviour is unchanged: user entries (SPP=0) reload the task shadow call stack, nested kernel entries (SPP=1) skip it.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  32. CVE-2026-99020

    In the Linux kernel, the following vulnerability has been resolved: regulator: tps6594-regulator: Fix n_linear_ranges for TPS65224 BUCK2-4 The TPS65224 BUCK2, BUCK3 and BUCK4 descriptors pass 4 as n_linear_ranges, but tps65224_bucks_2_3_4_ranges[] only has two entries, covering selectors 0x00-0x45. The linear range helpers loop over n_linear_ranges entries, so any lookup of a selector above 0x45 reads past the end of the array and treats whatever follows it as two more ranges. This happens on the normal registration path when the core checks the voltage constraints against every selector. TPS652G1 uses the same descriptors and is affected too. Use ARRAY_SIZE() so the count always matches the table.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  33. CVE-2026-99007

    In the Linux kernel, the following vulnerability has been resolved: drm/fb-helper: defer setup when fbdev_probe() fails, not just on -EAGAIN __drm_fb_helper_initial_config_and_unlock() calls drm_client_modeset_probe() first, which already fills in each mode_set->mode/num_connectors for every connected output, and only afterwards calls drm_fb_helper_single_fb_probe() to create fb_helper->fb and wire it into those mode_sets via drm_setup_crtcs_fb(). If drm_fb_helper_single_fb_probe() fails with anything other than -EAGAIN (e.g. dev->driver->fbdev_probe() itself fails), the function bails out before drm_setup_crtcs_fb() runs and before setting fb_helper->deferred_setup. The client is left with mode_sets that have a mode and connectors but mode_set->fb == NULL, and nothing marks this fb_helper as needing a retry. __drm_fb_helper_restore_fbdev_mode_unlocked() only skips committing when fb_helper->deferred_setup is set, so a later .restore() call (drm_lastclose() on process exit, in this report) commits the stale mode_set through drm_client_modeset_commit() -> drm_client_modeset_commit_atomic() -> __drm_atomic_helper_set_config(), which hits WARN_ON(!set->fb). Mark fb_helper->deferred_setup on any drm_fb_helper_single_fb_probe() failure, not just -EAGAIN, so restore keeps skipping the commit until a later hotplug event successfully re-probes and re-populates mode_set->fb. The real error code is still returned to the caller unchanged.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  34. CVE-2026-99008

    In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix NULL tty_dev dereference in rfcomm_dev_shutdown syzbot hit a NULL pointer dereference in rfcomm_dev_shutdown() when an RFCOMM tty is closed. rfcomm_dev_add() puts the new device on rfcomm_dev_list first and only then registers the tty device and saves it in dev->tty_dev. If that registration fails, dev->tty_dev is never set at all. The device can be looked up in the meantime, so an open() of /dev/rfcommN gets through rfcomm_tty_install() and attaches to it. When that tty is closed again, rfcomm_dev_shutdown() uses dev->tty_dev without checking it: Oops: general protection fault, probably for non-canonical address KASAN: null-ptr-deref in range [0x0000000000000040-0x0000000000000047] RIP: 0010:rfcomm_dev_shutdown+0x48/0xb0 net/bluetooth/rfcomm/tty.c:131 Call Trace: tty_port_shutdown+0x1bf/0x220 drivers/tty/tty_port.c:372 tty_port_close+0x4e/0x150 drivers/tty/tty_port.c:705 tty_release+0x359/0x1670 drivers/tty/tty_io.c:1718 __fput+0x418/0xa50 fs/file_table.c:512 rfcomm_dev_destruct() already copes with a NULL dev->tty_dev. Add the same check to rfcomm_dev_shutdown(), so the tty device is only moved when it was actually registered.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  35. CVE-2026-99009

    In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: connect the session socket without rfcomm_mutex An RFCOMM connect() issued while a BR/EDR link is being authenticated makes lockdep report a circular dependency, and the reported cycle is a real AB/BA between rfcomm_mutex and hdev->lock. rfcomm_security_cfm() is called from the HCI event path, which already holds hdev->lock: hci_rx_work() hci_event_packet() hci_cc_read_enc_key_size() [hdev->lock] hci_encrypt_cfm() [hci_cb_list_lock] rfcomm_security_cfm() [rfcomm_mutex] while an RFCOMM connect() from userspace takes the same two locks the other way round: rfcomm_sock_connect() rfcomm_dlc_open() [rfcomm_mutex] __rfcomm_dlc_open() rfcomm_session_create() kernel_connect() l2cap_sock_connect() l2cap_chan_connect() [hdev->lock] WARNING: possible circular locking dependency detected kworker/u131:1/1128 is trying to acquire lock: rfcomm_mutex, at: rfcomm_security_cfm+0x31/0x3e0 [rfcomm] but task is already holding lock: hci_cb_list_lock, at: hci_cc_read_enc_key_size+0x1d2/0xcc0 Chain exists of: rfcomm_mutex --> &hdev->lock --> hci_cb_list_lock hci_auth_complete_evt() and hci_encrypt_change_evt() reach the callback the same way. Both orders have to be seen in the same boot, which is why a BR/EDR connection alone is not enough to show it: a session set up by the remote side is created by rfcomm_accept_connection() in krfcommd, which calls kernel_accept() and never takes hdev->lock under rfcomm_mutex. Connecting a device that authenticates and encrypts the link and then calling connect() on an RFCOMM socket towards any address - the connect does not have to succeed, the order is recorded before the page timeout - reports it every time. Only the session socket has to be connected with the lock held, and it does not: nothing else can see the socket before it is put on the session list. So connect it first and take rfcomm_mutex afterwards, which removes the rfcomm_mutex -> hdev->lock order for good, rather than keeping the HCI event path out of rfcomm_mutex. rfcomm_session_create() becomes rfcomm_session_connect(), which returns the connected socket without touching the session list, and rfcomm_dlc_open() adds the session once it holds the lock again. If another opener added a session for the same pair while this socket was connecting, that session is used and this socket is dropped. __rfcomm_dlc_open() now takes the session it should use, and its state check runs after the lock is re-acquired, so a DLC that was opened or closed in the meantime is still handled. Over an existing ACL link the connection can complete before the session reaches the list, and the wakeup from the socket callback is then lost, so krfcommd is woken once the session is visible. Connecting without the lock opens a window in which the socket can be closed. The DLC is not on a session yet, so rfcomm_dlc_close() finds nothing to do and returns without touching it, and rfcomm_dlc_open() would then attach a DLC whose owner is gone. rfcomm_dlc_close() now marks such a DLC with RFCOMM_CLOSED, and rfcomm_dlc_open() checks the mark once it holds rfcomm_mutex again and drops the socket instead of attaching the DLC. The mark is cleared when an open starts, so a DLC that is reused is not affected. This covers both callers of rfcomm_dlc_open(), the socket and the tty layer.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  36. CVE-2026-99012

    In the Linux kernel, the following vulnerability has been resolved: Bluetooth: ISO: Serialize concurrent connect calls iso_sock_connect() checks the socket state before taking the socket lock and drops the lock again before setting up a connection. Two callers can both pass the admission check while the socket is open or bound. Caller A can copy its destination for route selection, then caller B can replace the socket destination before A binds or connects the CIS. A then uses B's destination with the route selected for its own request. B can also proceed after A attaches a connection and sets BT_CONNECT. For deferred BIS setup, B can bind a second BIS and overwrite iso_pi(sk)->conn, leaving the first connection's reference and conn->sk back-pointer stranded. Concurrent CIS connects can likewise replace the socket's connection. Later teardown only detaches the current connection, so a callback on the old connection can race with socket release and access a freed socket. KASAN reported: BUG: KASAN: slab-use-after-free in iso_sock_hold+0xf7/0x1b0 Call Trace: iso_sock_hold+0xf7/0x1b0 iso_conn_del+0x7b/0x1d0 iso_connect_cfm+0x186/0x16a0 hci_conn_failed+0x154/0x280 hci_abort_conn_sync+0x3dc/0x7d0 hci_cmd_sync_work+0x173/0x300 Allocated by task 121: sk_alloc+0x2b/0x6d0 bt_sock_alloc+0x29/0x370 iso_sock_alloc.constprop.0+0x19/0x300 iso_sock_create+0x94/0x100 Freed by task 121: kfree+0x121/0x3c0 __sk_destruct+0x42b/0x540 iso_sock_release+0x29d/0x340 __sock_release+0xa1/0x260 Check admission under the socket lock and mark the connect operation in progress before publishing its destination. Keep that flag set across route lookup and connection setup, rejecting another connect with -EBADFD before it can change the destination or attach a connection. Clear the flag after either helper returns, including on failure, so a failed setup can be retried. A separate flag is needed because the socket lock must be released before acquiring the HCI device lock, while BT_CONNECT requires an attached connection. Keep the existing state transitions and the deferred CIS completion through iso_sock_recvmsg(). Reject an existing socket attachment in __iso_chan_add() before taking a new reference or publishing either pointer, so every caller preserves the connection association. Keep the same-socket, same-connection success case for deferred CIS setup. Reject an attached socket before BIS setup so a reusable BIS is not claimed before the attachment is rejected. In CIS setup, reject a different HCI connection before iso_conn_add() and drop the per-attempt HCI hold directly. An unowned iso_conn may still carry another reference after detachment, so its destruction cannot be relied on to release that hold. iso_listen_bis() creates a fresh PA HCI/ISO pair under the device lock, so the temporary iso_conn_put() frees the ISO candidate and drops its HCI hold on rejection. iso_conn_ready() uses a freshly allocated, unpublished child with no connection, making the socket-side rejection unreachable.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  37. CVE-2026-98998

    In the Linux kernel, the following vulnerability has been resolved: drm/bridge: th1520-dw-hdmi: Fix remove() callback This driver stores struct th1520_hdmi * in platform drvdata, but th1520_dw_hdmi_remove() was reading it back as struct dw_hdmi * and passing it to dw_hdmi_remove(), so teardown runs on the wrong pointer. Retrieve struct th1520_hdmi * from platform drvdata and pass hdmi->dw_hdmi to dw_hdmi_remove().

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  38. CVE-2026-99000

    In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix shrinker accounting double-subtraction on nested external pins xe_bo_pin_external() and xe_bo_unpin_external() support nested pins, since the underlying ttm_bo_pin()/ttm_bo_unpin() maintain a pin_count refcount rather than a boolean. However, the shrinker accounting calls xe_ttm_tt_account_subtract() and xe_ttm_tt_account_add() are invoked unconditionally on every pin_external()/unpin_external() call, instead of only on the transition into and out of the pinned state. An external BO (dma-buf) can be pinned more than once while already pinned, for example when it has multiple attachments/importers, each independently calling xe_bo_pin_external(). Each such nested pin subtracts the BO's pages from the shrinker's accounting again, even though the BO's pages were already removed from consideration by the first pin. Symmetrically, each nested unpin adds them back again before the BO is actually unpinned. This desynchronizes the shrinker's page and object counts from reality, and since they are declared as signed long but interpreted as unsigned long in xe_shrinker_count(), the underflow can turn into an enormous shrinkable/purgeable page count, causing the shrinker to be invoked excessively under memory pressure. Guard the accounting calls with the same pin-count transition checks already used to guard the pinned_link list maintenance, so accounting is only updated on the outermost pin and the final unpin. While centralizing this logic into xe_bo_account_pin()/ xe_bo_account_unpin(), also close a second, related accounting gap affecting imported dma-bufs. For an imported bo's ttm_tt, xe's ttm_tt_populate hook (xe_ttm_tt_populate()) early-returns without calling xe_ttm_tt_account_add(), since TTM_TT_FLAG_EXTERNAL is set without TTM_TT_FLAG_EXTERNAL_MAPPABLE. However, TTM core's ttm_tt_populate() wrapper unconditionally marks the tt as populated on driver-hook success, so ttm_tt_is_populated() still reports true for it. xe_bo_account_pin()/xe_bo_account_unpin() trusted ttm_tt_is_populated() as a proxy for "these pages are accounted for by the shrinker", and would subtract/add pages for such a tt that were never added in the first place, again underflowing the shrinker's counts. This is reachable today via xe_bo_pin_external(), and would have become newly reachable via the fb-pin path once this patch routes __xe_pin_fb_vma() through xe_bo_pin_account() below, so fix it here rather than in a later patch, to avoid a commit in this series that introduces the regression before fixing it. Skip the accounting for imported bos, using the same EXTERNAL && !EXTERNAL_MAPPABLE test xe_ttm_tt_populate()/xe_ttm_tt_unpopulate() use to decide whether to act, via a new xe_ttm_bo_is_imported() helper (hoisted up from its only prior use site). v2: - Fix the critical issue caught by Sashiko AI review: the pin-count transition check introduced here was still bypassed by the fb-pin path (__xe_pin_fb_vma()/__xe_unpin_fb_vma()), which could leave a stale pinned_link entry and a permanent shrinker accounting leak when the fb-unpin performed the true last unpin. Addressed in a separate follow-up patch in this series rather than folded in here, since it is a distinct bug with its own Fixes: tag. - Drop the unneeded local "last_unpin" variable in xe_bo_unpin_external(), restoring the original inline bo->ttm.pin_count == 1 check; it was a no-op rename not used by any of the new accounting helpers, and was going to be deleted again by the follow-up patch anyway. v3: - Exclude imported dma-bufs from the pin/unpin shrinker accounting, fixing another underflow caught by Sashiko AI review. - Add a short comment on the backup-object pin site noting it's already populated/accounted at pin time, addressing (as a false-positive clarification, no code fix needed) a separate Medium-severity accounting-leak concern also caught by Sashiko AI ---truncated---

    Other OS & kernel

    unscored 0.2% exploit odds Fix listed
  39. CVE-2026-99003

    In the Linux kernel, the following vulnerability has been resolved: drm/panthor: validate userspace queue count against initialized firmware slot count In panthor_drv.c:panthor_ioctl_group_create(), the queue count is validated against the hardcoded maximum: if (!args->queues.count || args->queues.count > MAX_CS_PER_CSG) return -EINVAL; However, if the firmware reports fewer slots than MAX_CS_PER_CSG, panthor_fw_init_ifaces() will only initialize that smaller number of stream interfaces. If unprivileged userspace requests more queues than the firmware reported (but no more than MAX_CS_PER_CSG), cs_slot_prog_locked() fetches an uninitialized stream interface and may crash when dereferencing cs_iface->input->ringbuf_base.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  40. CVE-2026-99004

    In the Linux kernel, the following vulnerability has been resolved: drm/imagination: Size page table preallocation by device address Commit 0a8224058a58 ("drm/imagination: Fix page count for page table for map() interface") passed the device address to pvr_mmu_op_context_create(), but the preallocation is still sized from device_addr + sgt_offset with an exclusive end. The offset into the object's pages has no place in a device-virtual range, and the exclusive end allocates one table too many when the range ends on a table boundary. Count the tables from device_addr and the inclusive end of the range. The new calculation does not take page table indices into account. This fixes another issue with the previous implementation, where the difference between start and end indices could underflow when a mapping crossed a page table boundary. This would lead to the driver preallocating a huge number of MMU pages, exhausting system memory and triggering an out of memory panic. [Alessio: add paragraph to point out OOM bug being fixed, cc stable]

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  41. CVE-2026-99005

    In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Unmask interrupts only when ACTIVE is true There is a small race window between intel_rps_boost() reading a stale ACTIVE state and queuing rps->work, where ACTIVE may be changed via asynchronous calls triggered by wakeref drop. This means that rps_work() could be triggered after the GT has been parked, so unmasking RPS PM interrupts would happen without holding PM wakelock. This sequence of events may be observed during live_rc6_ctx_wa() selftest: 1) live_rc6_ctx_wa() -> intel_engine_pm_put() -> wakeref_put() ASYNC1) wakeref_put() callback -> __engine_park() -> intel_gt_pm_put_async() -> intel_gt_pm_put_async_untracked() -> intel_wakeref_put_async() ASYNC2) wakeref_put_async() callback -> __gt_park() -> intel_rps_park() -> intel_rps_clear_active() [clear ACTIVE] WITH INTERRUPTS: -> rps_disable_interrupts() -> cancel_work_sync(rps->work) -> rps_reset_interrupts() [rps->pm_iir = 0] WITHOUT INTERRUPTS (TIMER mode): -> rps_stop_timer() -> cancel_work_sync(rps->work) 2) live_rc6_ctx_wa() -> intel_gt_wait_for_idle() -> intel_gt_retire_requests_timeout() -> dma_fence_wait_timeout() -> ops->wait() [i915_fence_wait()] -> i915_request_wait_timeout() -> intel_rps_boost() -> intel_rps_is_active() [check ACTIVE] [OPEN RACE WINDOW] -> queue_work(rps->work) -> retire_requests() -> i915_request_retire() -> intel_rps_dec_waiters() [from 1 to 0] If ASYNC1 and ASYNC2 would execute during [OPEN RACE WINDOW], then: 3) rps_work() executes from the workqueue and may satisfy "(!pm_iir && !client_boost)" test (in TIMER mode rps->pm_iir is zeroed by an earlier rps_work() call or never gets a new value after previous intel_rps_unpark() event), so it jumps to "out" label, bypassing intel_rps_is_active() guard and executes gen6_gt_pm_unmask_irq(); 4) GT is parked and runtime PM wakelock is dropped, so only a raw reference in __gt_park() -> intel_display_power_put_async() remains for 100ms, then the MMIO write in gen6_gt_pm_unmask_irq() detects missing wakelock via assert_rpm_wakelock_held() and emits "RPM wakelock ref not held during HW access" tainting kernel. Commit 3e7abf814193 ("drm/i915: Extract GT render power state management") dropped the "if (rps->interrupts_enabled)" guard that gen6_pm_rps_work() had around this unmask in i915_irq.c. INTEL_RPS_ACTIVE brackets the same window, since it is set in intel_rps_unpark() before rps_enable_interrupts() and rps_start_timer() and cleared in intel_rps_park() before rps_stop_timer() and rps_disable_interrupts(). Skip unmasking when RPS is no longer active (reaching unmask operation is independent of INTERRUPT mode). This does not prevent RPS operation from resuming on the next unpark. In interrupt mode, intel_rps_unpark() calls rps_enable_interrupts(), which enables and unmasks the PM interrupts. In timer mode, it calls rps_start_timer(), restarting periodic engine-busyness evaluation. The timer generates software RPS events and queues rps_work() directly, independently of PM interrupt delivery. Neither mode requires the late worker to unmask interrupts while the GT is parked (cherry picked from commit ca4a6deadad15b91ee083afe445fa6bdbfb68206)

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  42. CVE-2026-98992

    In the Linux kernel, the following vulnerability has been resolved: namespace: don't copy an unmounted mount tree may_copy_tree() accepts a mount whose root is an nsfs or pidfs file before it checks whether that mount is mounted. This exception exists for nsfs and pidfs mounts. They are part of no mount namespace so neither check_mnt() nor is_mounted() would let them through and bind-mounting a nsfsfd or a pidfd wouldn't work. Problem is that exception also admits a bind mount of such a file when it was lazily unmounted and is only kept alive by a file descriptor: mount --bind /proc/self/ns/net /tmp/x exec 3< /tmp/x umount -l /tmp/x mount --rbind /proc/self/fd/3 /tmp/y With MS_REC or AT_RECURSIVE copy_tree() doesn't stop at the unmounted mount. It copies every mount that stayed attached to it as well. So if you have a bunch of overmounts over the nsfsfd or the pidfd the whole unmounted stack is copied. That's a bug. So refuse to walk an unmounted tree. Copying its root alone stays possible. So a bind mount of a namespace that is gone can still be recreated from a file descriptor on the old one. The file descriptor pins that mount and its root and __has_locked_children() only reads the direct children which don't leave the parent's list without namespace_sem. The internal mounts carry MNT_NS_INTERNAL instead of NULL and are still walked. Copying an unmounted tree recursively fails with EINVAL.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  43. CVE-2026-98993

    In the Linux kernel, the following vulnerability has been resolved: namespace: don't inherit MNT_UMOUNT in clone_mnt() MNT_UMOUNT gets raised on a mount that umount_tree() or umount_one() has taken out of its namespace. It's never cleared. __detach_mounts() unhooks a mount that carries it instead of unmounting it. disconnect_mount() lets an unmounted child stay attached only if its parent carries it. propagate_umount() takes it as the sign that a mount is going to be unmounted when it decides what else can be unmounted, where a chain of locked mounts ends and where a for reparenting an overmount. clone_mnt() copies the flags of the source and only masks MNT_INTERNAL_FLAGS which doesn't include MNT_UMOUNT. A mount that was lazily unmounted but is kept alive by a file descriptor can still be copied when its root is an nsfs or pidfs file because may_copy_tree() accepts those before checking whether the source is mounted at all: mount --bind /proc/self/ns/net /tmp/x exec 3< /tmp/x umount -l /tmp/x mount --bind /proc/self/fd/3 /tmp/y The mount on /tmp/y is attached to the caller's namespace with MNT_UMOUNT already set and every copy of it inherits the flag again. That causes a number of bugs: - Unlink its mountpoint from a mount namespace where it isn't one. __detach_mounts() takes it for a mount that was unmounted earlier, unhooks it from its parent and drops the reference the namespace holds on it. It stays in the namespace with one reference too few and as its own parent, so it can't be unmounted through the file descriptor anymore and the namespace never finds it again. When the namespace goes away it's leaked and points to a freed struct mnt_namespace that may_change_propagation() and anon_ns_root() read on the next propagation change or mount_setattr() through the file descriptor. - Make it shared and unmount a peer. trace_transfers() follows the flag from the peer into it and strips it from its peer group. - Let a propagated umount reach it. gather_candidates() marks it with T_UMOUNT_CANDIDATE but never puts it on the candidate list, so the mark is never cleared and every later propagated umount skips it. If it's the parent of a locked mount handle_locked() takes it as the cutoff and commits the locked child that should have stayed and disconnect_mount() leaves that child attached to it, unmounted under a mounted parent, which is what disconnect_mount() exists to prevent. When the namespace goes away umount_tree() visits the child a second time. And once __detach_mounts() has made it its own parent reparent() never finds the end of the chain of unmounted parents. A clone is a new mount that has never been unmounted. Add MNT_UMOUNT to MNT_INTERNAL_FLAGS so clone_mnt() never copies it. And warn when umount_tree() reaches a mount that already has it set.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  44. CVE-2026-98994

    In the Linux kernel, the following vulnerability has been resolved: statmount: read the parent of an unmounted mount under mount_lock statmount_mnt_basic() reads the ids of the parent through m->mnt_parent with namespace_sem held for reading. That's fine for a mount that is in a namespace. Everything above it is pinned by that namespace. STATMOUNT_BY_FD also accepts a file descriptor on a mount that has been unmounted on purpose and that only the file descriptor keeps alive. If that mount stayed attached to its parent when it was unmounted the parent is unmounted as well and nothing pins it for the child. The final mntput() unmounts the children under mount_lock alone and frees the parent afterwards. Concurrently, statmount_mnt_basic() reads m->mnt_parent twice while that can happen and can easily dereference a mount that's already gone. Read the parent of an unmounted mount under mount_lock. The parent can't be put while it is held and both ids come from the same mount. A mounted mount's parent is pinned by the namespace and a mount can't leave its namespace while namespace_sem is held, so the common case takes no global lock.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  45. CVE-2026-98995

    In the Linux kernel, the following vulnerability has been resolved: namespace: reset the old parent's ->overmount in mnt_change_mountpoint() __umount_mnt() resets ->overmount of the parent when it unmounts the mount that overmounts it. mnt_change_mountpoint() doesn't. It moves the mount to its new parent and leaves the old one pointing at it. For a mount that is moved beneath in attach_recursive_mnt() that doesn't matter. The new mount has already reset ->overmount of the old parent by the time the old top mount is moved onto it. It matters for reparent() though. propagate_umount() moves a surviving overmount onto the first ancestor that isn't going to be unmounted. The mount it was taken from is unmounted immediately afterwards. If a file descriptor keeps that unmounted mount alive ->overmount points at the moved mount. That's a dangling pointer and UAF as the moved mount is unmounted and freed. do_lock_mount() follows ->overmount from the target path under mount_lock. With a file descriptor on such a mount as the target of a mount beneath topmost_overmount() walks into the freed mount and do_lock_mount() takes references on whatever it finds there. So reset ->overmount of the old parent in mnt_change_mountpoint() the same way __umount_mnt() does. A mount's ->overmount is then always a mount that is attached to it.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  46. CVE-2026-98996

    In the Linux kernel, the following vulnerability has been resolved: fs: don't silently unmount busy mounts The propagate_mount_busy() helper exists to decide whether a synchronous can suceed. It does that by looking at the copies of the victims in the mounts its parent propagates to. One of those functions from propagation hell. It skips a copy that has child mounts except for the case of a single child mount covering the copy's root. That algorithm used to be exact. It isn't anymore. Originally only childless copies were unmounted during propagation. And 1064f874abc0 ("mnt: Tuck mounts under others instead of creating shadow/side mounts.") ended up adding covered mounts to both sides in one go. Along came 99b19d16471e ("mnt: In propgate_umount handle visiting mounts in any order") and that started to unmount more than before: [1]: A copy of a mount is unmounted when each of its children is either its overmount or a copy of the victim itself. In the former case the overmount gets reparented. In the latter case the copy of the victim will end up being unmounted. So propagate_umount() ended up being rewritten without adjusting propagate_mount_busy(). And currently propagate_mount_busy() doesn't look at copies of the victim that have two or more children nor a single child that is not the overmount. So any such copy in [1] is not checked for references. The result is that a synchronous unmount succeeds, pulling out a mount that is still in use. A container can run into this with its own mounts. The host shares a tree with the container and the host has a mount in that tree: mount -t tmpfs none /mnt mount --make-shared /mnt mount -t tmpfs none /mnt/a The container's /mnt is a slave copy of the host mount. The container now takes a detached copy of the tree and mounts that copy beneath its propagated copy of /mnt/a and keeps the file descriptor to the tree open: unshare -m --propagation unchanged mount --make-rslave / fd = open_tree(AT_FDCWD, "/mnt", OPEN_TREE_CLONE | AT_RECURSIVE) move_mount(fd, "", AT_FDCWD, "/mnt/a", MOVE_MOUNT_BENEATH) grep /mnt /proc/self/mountinfo 775 355 ... /mnt ... master:646 777 775 ... /mnt/a ... master:646 776 777 ... /mnt/a ... master:647 778 777 ... /mnt/a/a ... master:647 The now attached tree (777) is now mounted beneath the container's copy of /mnt/a. That's also where the host mount sits (as seen from the host mount namespace). So the propagated copy (776) of the host's mount is on top of its root and the copy of that (778) is inside it. Now the host runs: umount /mnt/a and it succeeds. The moved tree tree and the copy inside of it are gone from the container. Now only the propagated copy is left and it got reparented to where it was before: grep /mnt /proc/self/mountinfo 775 355 ... /mnt ... master:646 776 775 ... /mnt/a ... But the file descriptor still refers to the moved tree. So a synchronous umount detached a mount that is still in use. Teach propagate_mount_busy() the same checks that propagate_umount() does. It now checks for a single victim mount without children for which it can assume that MNT_LOCKED is cleared on every copy like propagate_umount() does. The copies form chains. IOW, when a copy itself receives propagation from the victim's parent then the mount at the same mountpoint inside that copy is a copy as well. Whether a mount receives propagation from the victim's can simply be checked by walking its masters. Walk each chain once from its top so we are sure that nested copies stay linear. Check every reference once of every copy that gets unmounted.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  47. CVE-2026-98997

    In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/userq: only accept doorbell BOs as queue doorbell amdgpu_userq_get_doorbell_index() pins any BO passed as doorbell_handle into the doorbell domain. For a regular BO, TTM moves it with ttm_bo_move_null() and its contents are lost. Since an importer on the same device gets the exporter's GEM object, a client can do this to a buffer another client shared with it. Reject BOs that were not created in the doorbell domain. v2: drop the error message, use a local abo variable (Christian) (cherry picked from commit f7497bbc19db4821c62b9d97b31c9086feb2d917)

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  48. CVE-2026-98982

    In the Linux kernel, the following vulnerability has been resolved: namespace: don't let a pseudo dentry become the root of a mount d_alloc_pseudo() hands out dentries for pipes, sockets and other files that are never anyone's child or parent. They carry DCACHE_NORCU and dentry_free() frees them right away because no lockless path walk can ever reach them. That holds as long as such a dentry isn't the root of a mount. But bind mounting /proc/self/fd/<fd> of such a file does exactly that. Most callers of alloc_file_pseudo() put their files on kernel-internal mounts and may_copy_tree() refuses those. bpf_token_create() doesn't. It places the token file on the bpffs mount the caller handed it and that mount is in the caller's mount namespace so the clone goes through: mount --bind /proc/self/fd/<token> <file> open_tree(tokfd, "", AT_EMPTY_PATH | OPEN_TREE_CLONE) + move_mount() __follow_mount_rcu() then loads ->mnt_root of that mount, reads d_seq and d_flags of the dentry and only then checks mount_lock. The dentry can be gone by then. The final mntput() of an unmounted parent unhooks a child that stayed attached to it under mount_lock alone. When the child's holder does the final put right after that the root is dput() and freed immediately while a walker that found the mount hashed still looks at it. Refuse to clone a mount with a DCACHE_NORCU dentry as its root. Nothing sensible can be done with a bind mount of a bpf token anyway.

    Other OS & kernel

    7.8 HIGH 0.2% exploit odds No fix listed
  49. CVE-2026-98983

    In the Linux kernel, the following vulnerability has been resolved: unshare: don't drop active namespace references that were never taken Active references on the namespaces of an nsproxy are taken when the nsproxy is installed into a task in switch_task_namespaces() and copy_namespaces() and dropped again by put_nsproxy() through deactivate_nsproxy(). But ksys_unshare() calls put_nsproxy() on an nsproxy that was never installed when set_cred_ucounts() fails. The new namespaces of that nsproxy go from zero to minus one and the namespaces shared with the caller lose a reference that belongs to the nsproxy the caller keeps using: WARNING: kernel/nscommon.c:171 at __ns_ref_active_put+0x1cd/0x230 nsproxy_ns_active_put deactivate_nsproxy ksys_unshare Afterwards the namespaces the caller lives in aren't listed by listns() anymore. set_cred_ucounts() only fails when alloc_ucounts() can't allocate and it only allocates when the real uid of the caller differs from its effective uid. Commit cefd55bd2159 ("nsproxy: fix free_nsproxy() and simplify create_new_namespaces()") separated the two cases on purpose. nsproxy_free() frees an nsproxy that was prepared but never installed and that's what a failed setns() uses in put_nsset(). Export it and use it for a failed unshare() as well.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed
  50. CVE-2026-98984

    In the Linux kernel, the following vulnerability has been resolved: dcache: don't put a mountpoint on a dentry that's being removed rmdir(), unlink() and rename() call dont_mount() on the victim and then detach_mounts() with the victim's inode locked. do_lock_mount() takes the inode lock of the mountpoint and checks cant_mount() so a mount can't show up after detach_mounts(). But attach_recursive_mnt() makes a second mountpoint for the root of the source mount so that the mounts already located at the destination can be put on top of it. No inode is locked for that one and d_set_mounted() only refuses a dentry that is unlinked. Between detach_mounts() and d_delete() the victim is still hashed: rmrace: b passed dont_mount() and detach_mounts(), sleeping T2: move_mount(S, /tmp/plcant/x, BENEATH) = 0 errno 0 () T1: rmdir(/tmp/plcant/d/b) = 0 errno 0 109 107 0:61 /d/b//deleted /tmp/plcant/x rw,relatime - tmpfs tmpfs rw 108 109 0:63 / /tmp/plcant/x rw,relatime - tmpfs T rw A bind mount of the directory that's being removed is moved beneath an existing mount while the rmdir() is located between the two calls. The mount ends up on the removed directory and nothing will ever detach it. Check cant_mount() in d_set_mounted() as well. dont_mount() raises the flag under d_lock before detach_mounts() runs so either the mountpoint is set first and detach_mounts() finds the mount or the flag is seen and the mount is refused.

    Other OS & kernel

    unscored 0.2% exploit odds No fix listed

The newest published CVE records from CVE.org and NVD, refreshed every few minutes, with severity, exploit odds and fix status.