CVEs of 2026.
Every CVE published in 2026 that we hold, ranked by exploit odds.
-
CVE-2026-99528
In the Linux kernel, the following vulnerability has been resolved: SUNRPC: fix netns use-after-free in write_gssp() While fuzzing with a customized syzkaller, I hit a refcount warning in xprt_alloc(), reached from a write to /proc/net/rpc/use-gss-proxy: refcount_t: addition on 0; use-after-free. WARNING: lib/refcount.c:25 at refcount_warn_saturate+0xf8/0x120 CPU: 0 PID: 10404 Comm: syz.0.17 Not tainted 7.3.0-rc1-00096-gcfebfd3db73d Call Trace: <TASK> xprt_alloc+0x83f/0x9d0 xs_setup_xprt+0xaf/0x3c0 xs_setup_local+0x47/0x7f0 xprt_create_transport+0x16c/0x730 rpc_create+0x38e/0x7f0 gssp_rpc_create+0xe2/0x180 set_gssp_clnt+0xba/0x1b0 write_gssp+0x200/0x310 proc_reg_write+0x240/0x330 vfs_write+0x2aa/0x1050 ksys_write+0x12a/0x250 do_syscall_64+0x117/0x750 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> create_use_gss_proxy_proc_entry() stores the struct net pointer as the proc entry's private data without taking a reference on it, and an open file descriptor does not pin the namespace either, as procfs only pins the proc_dir_entry. write_gssp() reads that pointer back with pde_data() and hands it to set_gssp_clnt(), which reaches xprt_init(): xprt->xprt_net = get_net_track(net, &xprt->ns_tracker, GFP_KERNEL); get_net_track() -> get_net() -> refcount_inc() is unconditional, so rpc_create() assumes its caller holds a reference on args.net. write_gssp() does not. Dropping the last ns.count reference does not make the file go away. __put_net() only queues cleanup_net() on a workqueue, and the remove_proc_entry() that fences off further writes runs from the rpcsec_gss pernet .exit method, that is, from inside cleanup_net(). A write landing between those two points increments a refcount that is already zero. cleanup_net() does not re-read ns.count, so the namespace is freed anyway and the rpc_xprt -- along with the AF_LOCAL socket opened for it -- is left pointing at freed memory. The resurrected count is visible to the rest of that teardown too: with CONFIG_IPV6_MROUTE the same cleanup_net() worker then trips !mr_can_free_table() in ip6mr_free_table(), which tests check_net() on the namespace it is freeing. It reduces to opening /proc/net/rpc/use-gss-proxy inside a new network namespace, calling setns() back to the original one to drop the last reference, and then writing "1" to the still-open descriptor. Take the reference in write_gssp() itself and refuse the write when the namespace is already gone. This is what procfs does for every other /proc/net file: get_proc_net() is maybe_get_net(PDE_NET(PDE(inode))) and seq_open_net() returns -ENXIO when it fails. PDE_NET() cannot be reused here because the parent directory /proc/net/rpc carries no namespace pointer. Adding a .pre_exit to rpcsec_gss_net_ops so the entry is removed earlier would only narrow the window, since pre_exit also runs from cleanup_net(). Live namespaces are unaffected: a write still returns the error from set_gssp_clnt(), a write of "2" still returns -EINVAL, and reads are untouched.
-
CVE-2026-99529
In the Linux kernel, the following vulnerability has been resolved: wifi: b43: fix use-after-free in b43_bcma_remove() b43_one_core_detach() frees the struct b43_wldev it is given the bus device of. b43_bcma_remove() then reads wldev->dev again to free the bus device, which is a read of freed memory. b43_ssb_remove() does not have the problem: it takes a copy of wldev->dev at the start. Do the same here.
-
CVE-2026-99531
In the Linux kernel, the following vulnerability has been resolved: ksmbd: verify transform SessionId matches the decrypted header When an encrypted request comes in, the decryption key is picked by the SessionId in the transform header, but the request is then authorized under whatever session the decrypted inner header names. Nothing ever compares the two, so on a connection with more than one session a client can get a request decrypted with one session's key and run it as another session. Encrypted requests are exempt from signing too, so a valid AEAD tag is the only proof of session identity, and it is checked against the wrong session. MS-SMB2 says the server must check that the transform SessionId matches the one in the decrypted SMB2 header and treat a mismatch as a protocol error. Add that check in __handle_ksmbd_work() after decryption, before dispatching: the message has to be at least one fixed SMB2 header, the first operation must not set SMB2_FLAGS_RELATED_OPERATIONS and its SessionId must match the transform SessionId, and every following non-related operation in a compound chain must carry the same SessionId. NextCommand offsets must be 8-byte aligned and stay inside the message; the bounds check is done by subtraction so it cannot wrap. When the decrypted payload is a compression transform, the existing decompression step runs first and the decompressed SMB2 message is checked instead, since a compression transform header carries no SessionId.
-
CVE-2026-99516
In the Linux kernel, the following vulnerability has been resolved: nvmet-fc: fix use-after-free in nvmet_fc_ls_create_connection() nvmet_fc_ls_create_connection() looks up the association with nvmet_fc_find_target_assoc(), which returns it with a reference held, and drops that reference as soon as the target queue has been allocated. iod->assoc is then dereferenced again by nvmet_fc_makeconnid() while building the connection id. The queue only borrows the pointer and takes no reference of its own. Once the lookup reference is dropped the association is kept alive solely by the reference taken when it was created, so a disconnect LS or a remote port unregister running concurrently can free it before nvmet_fc_makeconnid() reads it: BUG: KASAN: slab-use-after-free in nvmet_fc_handle_ls_rqst_work (drivers/nvme/target/fc.c:193 drivers/nvme/target/fc.c:1841 drivers/nvme/target/fc.c:1995 drivers/nvme/target/fc.c:2021) Read of size 8 at addr ffff888179f1b000 by task kworker/u9:2/1167 Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: nvmet-wq nvmet_fc_handle_ls_rqst_work Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120) print_report (mm/kasan/report.c:378 mm/kasan/report.c:482) kasan_report (mm/kasan/report.c:595) nvmet_fc_handle_ls_rqst_work (drivers/nvme/target/fc.c:193 drivers/nvme/target/fc.c:1841 drivers/nvme/target/fc.c:1995 drivers/nvme/target/fc.c:2021) process_scheduled_works (kernel/workqueue.c:3322 kernel/workqueue.c:3405) worker_thread (kernel/workqueue.c:3486) kthread (kernel/kthread.c:436) ret_from_fork (archkernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) </TASK> Freed by task 1167 on cpu 0 at 405.998150s: kasan_save_track (mm/kasan/common.c:57 mm/kasan/common.c:78) kasan_save_free_info (mm/kasan/generic.c:584) __kasan_slab_free (mm/kasan/common.c:253 mm/kasan/common.c:285) kfree (include/linux/kasan.h:235 mm/slub.c:2705 mm/slub.c:6405 mm/slub.c:6720) nvmet_fc_handle_ls_rqst_work (drivers/nvme/target/fc.c:1808 drivers/nvme/target/fc.c:1995 drivers/nvme/target/fc.c:2021) process_scheduled_works (kernel/workqueue.c:3322 kernel/workqueue.c:3405) worker_thread (kernel/workqueue.c:3486) kthread (kernel/kthread.c:436) ret_from_fork (archkernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) The buggy address belongs to the object at ffff888179f1b000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 0 bytes inside of freed 2048-byte region [ffff888179f1b000, ffff888179f1b800) Hold the lookup reference until the response has been built, and drop it on the error path as well.
-
CVE-2026-99521
In the Linux kernel, the following vulnerability has been resolved: rapidio: mport_cdev: fix use-after-free in mport_mm_close() A use-after-free vulnerability was identified in mport_mm_close() in drivers/rapidio/devices/rio_mport_cdev.c, identical to the pattern previously addressed in dma_req_free(). This is observable from userspace when an application creates an mmap mapping via the RapidIO character device and subsequently unmaps it (or terminates, triggering exit_mmap()). During munmap, mport_mm_close() is invoked and drops the mapping reference via kref_put(). If kref_put() drops the last reference, mport_release_mapping() is called, which frees the underlying rio_mport_mapping structure. The subsequent mutex_unlock() then dereferences map->md to unlock buf_mutex, leading to a use-after-free: mport_mm_close() -> mutex_lock(&map->md->buf_mutex); ... -> kref_put(&map->ref, mport_release_mapping); /* map is freed */ -> mutex_unlock(&map->md->buf_mutex); /* UAF: map used */ Fix this by caching map->md before kref_put() and using the cached pointer for mutex unlocking, ensuring that freed memory is not accessed.
-
CVE-2026-99515
In the Linux kernel, the following vulnerability has been resolved: iommufd: Fix event queue release use-after-free iommufd_eventq_fops_release() drops the file's users reference before reading eventq->ictx. Once that reference is dropped, IOMMU_DESTROY in another thread can remove and free the event queue, so the later load accesses freed memory. Read ictx while the users reference still pins the event queue, then drop the reference and put the saved context. The context reference taken by iommufd_eventq_init() keeps ictx valid until the put. Fault and vEVENTQ file descriptors share this release path.
-
CVE-2026-99503
In the Linux kernel, the following vulnerability has been resolved: ata: sata_fsl: Fix use-after-free of host_priv on probe() failure sata_fsl_host_stop() releases hcr_base and host_priv: static void sata_fsl_host_stop(struct ata_host *host) { struct sata_fsl_host_priv *host_priv = host->private_data; iounmap(host_priv->hcr_base); kfree(host_priv); } ->host_stop() is called by the driver core through the ata_host_stop() devres action which ata_host_start() registers, so it is called both when the device is unbound and when probe() fails after the host has been started. The error_exit_with_cleanup label of sata_fsl_probe() releases hcr_base and host_priv as well, and it is reachable from the two device_create_file() calls which are done after the host has been activated. In that case sata_fsl_host_stop() runs on an already freed host_priv, resulting in a use-after-free and a double iounmap()/kfree(). Add a separate error label for the failures happening after the host has been activated, which only detaches the host and leaves hcr_base and host_priv to sata_fsl_host_stop(). Note that ata_host_detach() is dropped from error_exit_with_cleanup, as that label is now only reachable while host is still NULL.
-
CVE-2026-99505
In the Linux kernel, the following vulnerability has been resolved: apparmor: fix a use-after-free in aa_lookupn_ns() aa_lookupn_ns() takes a reference on the namespace it finds with aa_get_ns(), which is kref_get() on the reference count that the namespace is released through, without checking whether the namespace is still in use. A concurrent removal of a ":"-prefixed namespace looks the same namespace up and only then takes the parent lock to remove it, so the last reference can be dropped between the lookup and the aa_get_ns() call: the reference count then reports the increment on a zero count and the kernel classifies the following use of the object as a use-after-free. A user with CAP_MAC_ADMIN can trigger this by writing a ":<name>" removal and a ":<name>/<profile>" removal to /sys/kernel/security/apparmor/.remove concurrently. refcount_t: addition on 0; use-after-free. WARNING: lib/refcount.c:25 at refcount_warn_saturate+0xc0/0xe0, CPU#6 Call Trace: <TASK> aa_lookupn_ns+0xa9/0xc0 aa_remove_profiles+0x4fb/0x730 ? __kvmalloc_node_noprof+0x219/0x5c0 ? __pfx_aa_remove_profiles+0x10/0x10 ? aa_loaddata_alloc+0x65/0x1f0 ? _copy_from_user+0x2d/0x80 ? aa_loaddata_alloc+0x111/0x1f0 profile_remove+0x2ee/0x4a0 vfs_write+0x21e/0xcf0 ? rcu_core+0x29c/0x1740 ? timerqueue_linked_add+0x1f4/0x3d0 ? __pfx_vfs_write+0x10/0x10 ? mutex_lock+0x81/0xe0 ? __pfx_mutex_lock+0x10/0x10 ? __pfx_rcu_core+0x10/0x10 ? __pfx_hrtimer_update_next_event+0x10/0x10 ? mutex_unlock+0x7b/0xd0 ? fdget_pos+0x24d/0x4b0 ksys_write+0xf7/0x1c0 ? __pfx_ksys_write+0x10/0x10 ? restore_fpregs_from_fpstate+0x37/0xc0 do_syscall_64+0xf9/0x540 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> Fix by rejecting a namespace whose reference count is zero.
-
CVE-2026-99506
In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix use-after-free of a new anon folio For a fault in a private mapping with nothing in the page cache, hugetlb_no_page() allocates a folio, locks it and maps it. The folio has one reference, which belongs to the page table entry from then on. After dropping the page table lock the function still sets the migratable flag of the folio and unlocks it. Whoever zaps the entry in between frees the folio. The fault holds the fault mutex and the lock of the vma. MADV_DONTNEED and the first unmap of a hole punch, hugetlb_vmdelete_list(), do not take the fault mutex, and a private vma only has a lock if it owns a reservation map: not with MAP_NORESERVE, and not in the child after fork(). Then the flag is set in, and folio_unlock() is called on, a folio that is free or has a new owner. A surplus page goes back to the page allocator while it is locked: BUG: Bad page state in process init pfn:108e00 flags: 0x200000000000059(locked|uptodate|dirty|head|node=0|zone=2) page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set A page of the pool can be given to the next user, of any file, who locks it and loses the lock to the late folio_unlock(): kernel BUG at mm/filemap.c:1532! hugetlb_no_page+0x111b/0x23e0 hugetlb_fault+0x3a9/0x14a0 An unprivileged process is enough: threads that write to a MAP_PRIVATE | MAP_NORESERVE hugetlb mapping, threads that call MADV_DONTNEED on it, and one that takes the freed pages for another file. Until commit 3a47c54f09c4 ("hugetlbfs: revert use i_mmap_rwsem for more pmd sharing synchronization") the fault held i_mmap_rwsem for reading, which everybody who zaps takes for writing. The lock that commit bf4916922c60 ("hugetlbfs: extend hugetlb_vma_lock to private VMAs") gave to private vmas closed the window again, but only for those with a reservation map. Be done with the folio before the page table lock is dropped, as hugetlb_wp() is with its copy. The function already unlocks page cache folios under that lock. Original fix generated by an LLM and sent in private by Josef. [[email protected]: simplify+move comment]
-
CVE-2026-99492
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Advertise SW_MUTE_DEVICE capability prior to registration Input subsystem guidelines require that device capabilities are advertised before the input device is registered. The Wacom driver was violating this by advertising the SW_MUTE_DEVICE capability post-registration in wacom_set_shared_values() (and duplicating it in device-specific setup cases). Resolve this by moving the SW_MUTE_DEVICE capability setup to wacom_setup_touch_input_capabilities() for all touch devices that support it. For generic touch devices whose capabilities depend on mute switch usages parsed from a sibling Pen/Pad interface, defer registration with -EPROBE_DEFER until the sibling has parsed its descriptors and initialized shared capabilities.
-
CVE-2026-99494
In the Linux kernel, the following vulnerability has been resolved: s390/zcrypt: Fix out-of-bounds ptr advance in cca_query_crypto_facility() The FQ reply parser code blindly advanced the walk pointer by a length value read directly from the hardware reply payload without checking that the advance stayed within the allocated reply buffer. A corrupt or malicious device response could push ptr beyond the cprbmem region, causing an out-of-bounds dereference or kernel memory exposure via the subsequent memcpy(). Fix this by tracking the remaining reply buffer space in a variable and validating each device-supplied length field against it before advancing or dereferencing the pointer.
-
CVE-2026-99497
In the Linux kernel, the following vulnerability has been resolved: s390/probes: Fix wrong opcode for cgrb fixup The last byte of the cgrb instruction is 0xe4, however the probes code compares against 0xe6. Fix it.
-
CVE-2026-99483
In the Linux kernel, the following vulnerability has been resolved: ALSA: pcmtest: handle multiple wraps in random capture fill The random capture helpers assume that the data generated for one timer tick wraps the DMA ring at most once. However, b_rw describes 200 ms of audio because the timer runs at 5 Hz, so it can be several times larger than a small ring. For 48 kHz, S16_LE, four-channel capture with a 512-frame buffer, the DMA ring is 4096 bytes while one tick generates 76800 bytes. After filling the 4096-byte tail, the existing code issues a second 72704-byte write from the ring base, writing 68608 bytes beyond the ring. Both interleaved and non-interleaved capture are affected. KASAN reports the first write into the adjacent free page as a use-after-free in the random-byte generator. The underlying defect is an out-of-bounds write from the live DMA ring, not a stale DMA allocation. Split each random write repeatedly at the interleaved ring or per-channel block boundary. Keep the hardware-pointer update exactly once after the complete logical write. The issue reproduced on three of three clean boots. With this change, the same vulnerable geometry completed six times without a sanitizer finding. Boundary, pattern-fill, no-timer, open/close, and module-reload controls also completed normally. snd-pcmtest is a test driver, and selecting random fill requires an administrator-controlled module parameter. The written values come from the kernel random generator; no privilege escalation or attacker-controlled write primitive was demonstrated.
-
CVE-2026-99488
In the Linux kernel, the following vulnerability has been resolved: klist: avoid accesses after waking klist_remove() klist_remove() waits until a node is unreferenced so that its caller can free the containing object. klist_release() currently publishes waiter->woken and wakes the waiter before its final accesses to the waiter and node. klist_remove() can then return, allowing its stack waiter and the containing object to be freed or reused while klist_release() is still running. In particular, bus_remove_driver() can free drv->p while __device_attach() walks the same bus klist with bus_for_each_drv(). On an arm64 Cortex-A72 system, an unpatched 7.2.0-rc3 kernel with CONFIG_PREEMPT_RT=y and CONFIG_KASAN=y reproduced the bug through the in-tree I2C/at24 path. KASAN reported a use-after-free in klist_dec_and_del() reached from klist_next()/bus_for_each_drv() while at24 was being unregistered. Clear n_klist and take a task reference before publishing woken. Use release/acquire accesses for that publication and wake the referenced task. The task reference keeps the waiter task alive if it returns and exits before wake_up_process().
-
CVE-2026-99489
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Redesign shared sibling data lifecycle The Wacom driver coordinates state between sibling interfaces of the same physical device using a shared structure 'wacom_shared' inside 'wacom_hdev_data'. The driver kept a volatile representative pointer 'data->dev' pointing to a sibling 'hid_device' for physical path comparisons during sibling matching. This pointer management is fragile. When the representative device is disconnected, wacom_remove_shared_data() failed to clear/update 'data->dev', leading to a Use-After-Free vulnerability when subsequent sibling probes dereference the dangling 'data->dev' pointer. Resolve this issue by redesigning the sibling data lifecycle: - Eliminate the volatile 'data->dev' representative pointer completely - Redesign 'wacom_hdev_data' to store stable static copies of the required attributes upon first allocation: 'phys' path string, 'vendor', 'product' IDs and the sibling's 'device_type' - Use these static attributes for stable sibling matching in wacom_are_sibling() and wacom_get_hdev_data() This ensures sibling matching remains safe and stable even if individual siblings are dynamically added or removed. To secure the lifecycle against concurrent probe/disconnect races: - Switch kref_put() to kref_put_mutex() in wacom_remove_shared_data() to serialize refcount drops with list traversal and lookup - Modify wacom_release_shared_data() to assume the list lock is already held Also, do not accumulate the 'device_type' capability flag during subsequent sibling probes. Keeping only the first probed sibling's device_type exactly preserves the original sibling matching behavior without introducing side effects.
-
CVE-2026-99490
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Fix Use-After-Free in wacom_bamboo_pad wacom_bamboo_pad_pen_event() accesses wacom->shared->pen locklessly relative to wacom_remove_shared_data() which nullifies it. This can lead to a Use-After-Free if the sibling device is removed while events are being processed. Resolve this by introducing RCU protection for pen and touch pointers: - Annotate 'pen' and 'touch' in wacom_shared struct with __rcu. - Wrap lockless readers in wacom_bamboo_pad_pen_event() with rcu_read_lock() and rcu_dereference(). - Update writers in wacom_sys.c using rcu_assign_pointer(). - Use rcu_dereference_protected for comparisons under wacom_udev_list_lock. - Also use rcu_access_pointer in wacom_sibling_pending() and wacom_mode_change_work() to avoid warnings (while lockless access in the latter remains a pre-existing issue).
-
CVE-2026-99491
In the Linux kernel, the following vulnerability has been resolved: HID: wacom: Fix Use-After-Free in wacom_intuos_pad wacom_intuos_pad() accesses wacom->shared->touch_input locklessly inside the interrupt handler context. If the Touch sibling device is disconnected, wacom_remove_shared_data() clears 'touch_input' outside any lock, creating a Time-of-Check to Time-of-Use (TOCTOU) race condition where a preempted reader in interrupt context dereferences the freed pointer, leading to a Use-After-Free. Resolve this by introducing RCU protection for the touch_input pointer: - Annotate 'touch_input' in wacom_shared struct with __rcu - Wrap all lockless readers in wacom_wac.c with guard(rcu)() and rcu_dereference() using a unified wacom_report_touch_mute() helper - Update writers in wacom_sys.c using rcu_assign_pointer() - Call synchronize_rcu() in wacom_remove_shared_data() to ensure all active RCU readers have finished before the input device is freed Also wrap wacom_set_shared_values() and touch/pen assignments in wacom_add_shared_data() inside the wacom_udev_list_lock to serialize concurrent probe assignments, and verify that 'shared->touch == hdev' before setting touch_input to prevent concurrent sibling probe state desynchronization.
-
CVE-2026-99475
In the Linux kernel, the following vulnerability has been resolved: genirq: Defer kfree(irqaction) until irq_thread_dtor() finishes When an interrupt thread exits abnormally via do_exit() (e.g. the interrupt handler oopses) without returning from irq_thread(), a concurrent call to free_irq() could free the irqaction before the irq_thread_dtor() exit task work runs. irq thread (oopsed) free_irq() ------------------- ---------- do_exit() exit_mm() complete_vfork_done() -------> kthread_stop() returns exit_files() ... kfree(action) exit_task_work() irq_thread_dtor() action->... <- use-after-free Track the pending exit work with the IRQTF_EXIT_WORK thread flag, and have __free_irq() wait for the bit to clear before kfree(). irq_thread_dtor() only runs on irq_thread abnormal exit. If that dtor also faults, free_irq() will hang indefinitely, but double IRQ thread faults require a reboot anyways. [ tglx: Add missing include ]
-
CVE-2026-99477
In the Linux kernel, the following vulnerability has been resolved: fs/proc/task_mmu: pin mm_users in do_pagemap_scan() The PAGEMAP_SCAN ioctl takes mmap_read_lock() on an mm obtained from /proc/<pid>/pagemap without holding a reference to mm_users. proc_mem_open() deliberately grabs only mm_count, so a consumer that touches the address space has to call mmget_not_zero() first. Every other consumer in this file does -- m_start(), do_procmap_query(), show_smaps_rollup() and pagemap_read() -- but do_pagemap_scan() does not. Without that reference the target can reach exit_mmap() concurrently, and exit_mmap() calls unmap_vmas() while holding mmap_lock only for reading, which does not exclude the scanner. For ordinary VMAs this is harmless, as free_pgtables() and remove_vma() run afterwards under mmap_write_lock. A shared hugetlb VMA is different: __hugetlb_zap_end() frees the VMA's hugetlb_vma_lock inside the read-locked phase. walk_hugetlb_range() can therefore load vma->vm_private_data, have the lock freed underneath it, and then down_read() a freed rw_semaphore. The load happens before the freeing side clears the pointer, so this is a use-after-free and not a NULL dereference. Any unprivileged user can reach it with no huge pages configured, as hugetlb_reserve_pages() allocates the lock before the VM_NORESERVE early return. Pin mm_users across the scan, the way the other consumers do. mmput() from the exiting task can then no longer reach exit_mmap() while a walk is in progress. [[email protected]: remove unneeded & undesirable test for !mm]
-
CVE-2026-99479
In the Linux kernel, the following vulnerability has been resolved: fbdev: atmel_lcdfb: Prevent FIFO work after removal The LCD controller IRQ schedules sinfo->task to recover from a FIFO underflow. Probe currently requests the IRQ before initializing the work, so an early interrupt can schedule an uninitialized work item. The probe error path and remove path cancel the work before freeing the IRQ. A FIFO-underflow interrupt can schedule the work again after that cancellation. framebuffer_release() may then free sinfo while the work is still pending. KASAN reported a use-after-free in atmel_lcdfb_task() when an underflow interrupt occurred during removal. With the IRQ freed before the work was cancelled, the same test completed without a kernel diagnostic. Initialize the work before requesting the IRQ. In both cleanup paths, free the IRQ before cancelling the work so that it cannot be scheduled again after cancellation.
-
CVE-2026-99480
In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix TOCTOU race between GROUP_REGISTERED check and erase panthor_group_destroy() checks the GROUP_REGISTERED mark and then calls xa_erase() without holding the xarray lock across both. If the handle is destroyed by another thread in between, and a concurrent GROUP_CREATE reuses the freed ID, the first destroy erases and releases the new, still-initializing group, leading to a use-after-free in panthor_group_create(). Do the mark check and erase atomically under xa_lock().
-
CVE-2026-99481
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_vhci: Pin module for debugfs file operations An open debugfs file retains its file_operations pointer in the debugfs proxy state. However, force_suspend_fops, force_wakeup_fops, aosp_capable_fops, and force_devcoredump_fops have no .owner set to THIS_MODULE. As a result, full_proxy_open_regular() calls fops_get() which succeeds without taking a reference to the hci_vhci module. When userspace opens any of these debugfs files and later closes the /dev/vhci file descriptor (triggering vhci_release() and debugfs file removal), the open debugfs file descriptor remains valid in userspace. Because the module refcount was not incremented, the hci_vhci module can be unloaded via delete_module (rmmod hci_vhci). When the userspace process subsequently closes the debugfs file descriptor, full_proxy_release() accesses the already unmapped file_operations structure, resulting in a kernel page fault / oops: BUG: unable to handle page fault for address: fffffbfff846f18b #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page Oops: Oops: 0000 [#1] SMP KASAN NOPTI RIP: 0010:full_proxy_release+0x8e/0x140 Call Trace: <TASK> __fput+0x39f/0xa60 fput_close_sync+0xff/0x200 __x64_sys_close+0x8c/0xf0 do_syscall_64+0xc3/0x590 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> Modules linked in: ... [last unloaded: hci_vhci(E)] The issue was discovered via manual code audit of drivers/bluetooth/hci_vhci.c and verified on a Linux 7.3-rc6 test VM with CONFIG_BT_VHCI=m by keeping a debugfs file open across controller teardown and module unload. Set .owner = THIS_MODULE on all four file_operations structures so that debugfs pins the module until all file descriptors are closed.
-
CVE-2026-99469
In the Linux kernel, the following vulnerability has been resolved: media: gspca: use vb2_video_unregister_device() on disconnect gspca uses vb2_fop_release(), but gspca_disconnect() only unregisters the video device. If the queue owner closes the device after USB disconnect, vb2_fop_release() releases the queue and invokes gspca_stop_streaming() at that point. gspca_stream_off() calls subdriver stop callbacks and usb_set_interface() through gspca_dev->dev. By the time the late close runs, the USB core can have freed the usb_device, resulting in a use-after-free. This was observed as a KASAN use-after-free in sd_stopN(). Use vb2_video_unregister_device() so the queue is released and streaming is stopped synchronously during disconnect, while the usb_device is still valid. Since the helper takes the queue lock, which is usb_lock, call it after dropping that lock.
-
CVE-2026-99470
In the Linux kernel, the following vulnerability has been resolved: media: cx23885: unregister DVB bus when SP2 CI setup fails The DVBSKY S950C, DVBSKY T980C and TechnoTrend CT2-4500 CI paths register the DVB bus before attaching their SP2 CI client. If that client cannot be created, bound, or pinned, the current error path removes the I2C frontend components and only deallocates the frontend list, leaving the registered DVB adapter behind. Removing an I2C demod before unregistering the DVB bus can also expose the use-after-free ordering fixed for the normal remove path. Unregister the DVB bus immediately when SP2 CI setup fails, before the existing I2C client cleanup. The bus helper empties the frontend list, so the later frontend deallocation has nothing left to release. Keep failures from vb2_dvb_register_bus() on the existing cleanup path. Also release an unbound SP2 client and propagate the actual I2C creation or CI registration error. This issue was identified during our ongoing static-analysis research while reviewing kernel code.
-
CVE-2026-99473
In the Linux kernel, the following vulnerability has been resolved: KVM: guest_memfd: Gracefully handle xarray errors when binding a memslot If inserting a memslot into a guest_memfd's bindings xarray fails, propagate the error back to the caller, i.e. fail memslot creation as well. Signalling success and continuing on with memslot creation results in use-after-free, as the guest_memfd instance will remain reachable via the memslot after the file is freed (kvm_gmem_release() won't nullify the file pointer due to lack of a valid binding). Opportunistically WARN and reject binding if KVM_MEMSLOT_GMEM_ONLY is already set, partly to guard against goofs elsewhere, but mostly so that KVM doesn't need to worry about clobbering flags when unwinding on failure. Regarding the unwind, the slot must be fully prepared before inserting it into the bindings, at which point the slot becomes reachable. I.e. waiting to update the slot in order to avoid the ugly unwind isn't an option. And as part of the unwind, explicitly nullify the relevant bindings, as xarray can store a subset of entries when populating a range.
-
CVE-2026-99474
In the Linux kernel, the following vulnerability has been resolved: HID: hiddev: keep state alive through disconnect unlock mutex_unlock() clears the mutex owner before taking its wait lock. A thread spinning in the final hiddev file release can acquire existancelock after hiddev_disconnect() clears the owner, then free hiddev before the disconnecting thread reaches the mutex wait lock. This causes a use-after-free in the mutex slow unlock path. Give the connection and each open file an explicit reference. Drop each reference only after its existancelock critical section has completed, so neither unlock path can free the mutex while the other is still using it.
-
CVE-2026-99460
In the Linux kernel, the following vulnerability has been resolved: mptcp: hold MP_JOIN msk ref when cloning reqsk TCP request migration clones pending request sockets with inet_reqsk_clone(). For MPTCP MP_JOIN requests this byte-copies subflow_req->msk, but the clone does not own a reference. The original and cloned requests can consequently drop the same msk reference, leaving one request with a dangling pointer. This manifests as a KASAN slab-use-after-free in subflow_req_destructor(): BUG: KASAN: slab-use-after-free in subflow_req_destructor (net/mptcp/subflow.c:45) Write of size 4 at addr ff1100010e008d40 by task swapper/0/0 CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 7.2.0-rc5-00353-gc27e36054537 #10 PREEMPT(full) Call Trace: subflow_req_destructor (net/mptcp/subflow.c:45) subflow_v4_req_destructor (net/mptcp/subflow.c:694) __reqsk_free (net/ipv4/inet_connection_sock.c:906) reqsk_timer_handler (include/net/request_sock.h:137 net/ipv4/inet_connection_sock.c:1147) Allocated by task 10014: sk_prot_alloc (net/core/sock.c:2246) sk_clone (net/core/sock.c:2488) mptcp_sk_clone_init (include/net/sock.h:1848 net/mptcp/protocol.c:3564) subflow_syn_recv_sock (net/mptcp/subflow.c:883) tcp_check_req (net/ipv4/tcp_minisocks.c:934) Freed by task 0: slab_free_after_rcu_debug (include/linux/kasan.h:235 mm/slub.c:2677 mm/slub.c:6439) rcu_core (kernel/rcu/tree.c:2645 kernel/rcu/tree.c:2897) Last potentially related work creation: kmem_cache_free (mm/slub.c:2638 mm/slub.c:6377 mm/slub.c:6504) __sk_destruct (net/core/sock.c:2289 net/core/sock.c:2391) sk_destruct (net/core/sock.c:2419) __sk_free (net/core/sock.c:2430) sk_free (net/core/sock.c:2441) mptcp_close (include/net/sock.h:2020 net/mptcp/protocol.c:3399) inet_release (net/ipv4/af_inet.c:442) The buggy address belongs to the cache MPTCP of size 2968 The buggy address is 128 bytes inside a freed 2968-byte region A non-NULL subflow_req->msk means that the request owns one reference. The third ACK can concurrently transfer the original request reference to the child and release it, so taking an unconditional hold on the copied pointer is unsafe. MPTCP sockets use SLAB_TYPESAFE_BY_RCU and all current inet_reqsk_clone() callers run in an RCU read-side critical section. Document and lockdep-check that calling-context requirement. Read the pointer from the original request and acquire a reference only if it is still live. Use refcount_inc_not_zero_acquire() so the subsequent ownership validation cannot be reordered before the try-get, then re-read the original request to verify that it still owns the same msk. If either check fails, clear the clone pointer; otherwise its normal destructor balances the new reference. Mark the ownership-transfer store with WRITE_ONCE() to match the lockless reads. The following patch completes the clone fixup for MP_CAPABLE token ownership. Both patches carry the same Fixes tag and are required for stable backports.
-
CVE-2026-99461
In the Linux kernel, the following vulnerability has been resolved: mm: khugepaged: fix swap entry value to folio_pfn() Patch series "mm: khugepaged: fix tracepoint UAF", v5. The khugepaged tracepoints take a folio pointer and call folio_pfn(), but by then the folio may no longer be valid: freed after folio_put(), folio_unlock() or pte_unmap_unlock(), or not a folio at all but an xarray-encoded swap entry. On classic SPARSEMEM, dereferencing it oopses khugepaged as soon as the trace event is enabled; on other memory models it merely prints a bogus pfn. Pass the pfn to the tracepoints directly, captured while the folio is still pinned, closing the use-after-free windows in mm_khugepaged_scan_file(), mm_khugepaged_scan_pmd() and mm_khugepaged_collapse_file(). This patch (of 3): When the swap entries found exceed max_ptes_swap, the loop is left via break with folio still holding the xarray value that encodes the swap entry, not valid folio pointer. That value is passed to trace_mm_khugepaged_scan_file(), which feeds it to folio_pfn(). On FLATMEM and SPARSEMEM_VMEMMAP, the page_to_pfn() is plain pointer arithmetic, so the trace event merely prints bogus scan_pfn. On classic SPARSEMEM, the page_to_pfn() reads page->flags, dereferencing the tiny encoded integer and oopsing khugepaged whenever the trace event is enabled. So when folio is the swap entry value, simply set pfn to -1, just like exhausted scan naturally. And the folio_put() has maybe dropped the last reference of folio. The trace_mm_khugepaged_scan_file() is left with a dangling folio pointer. so using the folio_pfn() before dropping the reference, closing use-after-free window.
-
CVE-2026-99463
In the Linux kernel, the following vulnerability has been resolved: mm/rmap: don't discard lazyfree THPs at PMD level __discard_anon_folio_pmd_locked() clears a lazyfree THP's PMD before it determines whether the folio can be discarded, and restores it if the folio is dirty or has extra references. It is done under only the PMD lock and the anon_vma read lock inside try_to_unmap_one() and no mmap lock is held. The temporarily none PMD causes UAF. A parallel munmap() or mremap() is supposed to serialize with it on the PMD lock, but zap_pmd_range() (called by munmap()) and move_page_tables() (called by mremap()) do not take the lock when they see the temporarily none PMD and skip the PMD. There is no more page table walk after the none PMD is restored: - munmap(): free_pgtables() waits in unlink_anon_vmas() for the anon_vma lock, then free_pmd_range() drops the restored PMD as bad without removing the rmap, so the folio keeps a stale mapcount. - whole-VMA MREMAP_DONTUNMAP: dontunmap_complete() unlinks the source VMA from its anon_vma while the restored PMD still maps the folio. - plain mremap(): the THP is not moved but unmapped, so the THP's data is lost. In the first two cases, the folio stays mapped, but no VMA that maps it is linked to its anon_vma. When the anon_vma is freed, it is still reachable when one rmap walks the folio. Racing lazyfree reclaim against MREMAP_DONTUNMAP as an unprivileged user reproduces a KASAN use-after-free in folio_lock_anon_vma_read() as reported in the Closes link. One solution is to use an invalidated PMD instead of a cleared one until the discard is committed, but it needs arch fixes first. 1. GUP-fast still follows an invalidated PMD on riscv, LoongArch and s390. 2. sparc64 miscounts thp_pte_count when an invalidated PMD is set again or cleared. To keep the fix simple for backport, stop discarding lazyfree THPs at PMD level instead. try_to_unmap_one() splits the PMD and discards the folio at PTE level. unmap_huge_pmd_locked() and __discard_anon_folio_pmd_locked() are left in place, unused, to minimize this fix for backport and the invalidated PMD approach is planned as a follow-up series to use them again.
-
CVE-2026-99464
In the Linux kernel, the following vulnerability has been resolved: media: redrat3: fix UAF in probe error path leaving rc device registered redrat3 stores its device name and phys path inside the main rr3 structure, and the rc device's device_name and input_phys point into rr3. When the RC device is registered, it keeps those pointers. KASAN: slab-use-after-free in string_nocheck lib/vsprintf.c:648 Read of size 1 at addr ffff888051fda758 by task udevd/7464 Call Trace: string_nocheck lib/vsprintf.c:648 [inline] string+0x216/0x2d0 lib/vsprintf.c:730 vsnprintf+0x74a/0xef0 lib/vsprintf.c:2945 vscnprintf+0x41/0x90 lib/vsprintf.c:3014 sysfs_emit+0x10e/0x180 fs/sysfs/file.c:761 input_dev_show_name+0x58/0x70 drivers/input/input.c:1282 Allocated by task 10: redrat3_dev_probe+0x477/0x2570 drivers/media/rc/redrat3.c:1023 Freed by task 10: redrat3_delete drivers/media/rc/redrat3.c:466 [inline] redrat3_dev_probe+0x1bf4/0x2570 drivers/media/rc/redrat3.c:1124 Syzkaller triggers this via usb probing. It probes the RedRat3 USB interface, which calls redrat3_dev_probe() in redrat3.c. That function allocates rr3, then builds an rc device whose name points into rr3 via redrat3_init_rc_dev() in redrat3.c, and registers it with rc_register_device(). When the detector enable fails after the RC device is registered, the probe jumps to the led_free path. That path unregisters the LED but does not unregister the RC device before freeing rr3 via redrat3_delete() in redrat3.c. The RC device still holds device_name = rr3->name which is now freed. Later udevd reads /sys/.../input device name via sysfs_emit() in file.c, which calls input_dev_show_name() in input.c, which emits dev->name which is the freed rr3->name. When the detector enable fails after the RC device is registered, the error path must not leave the RC device registered. Make the probe error path clean up the same way redrat3_dev_disconnect() does. This change should be safe because the RC device is fully registered at this point and its teardown via rc_unregister_device() is protected by the input device mutex, and rr3 is still alive during unregister so device_name remains valid until after unregister. The URBs are killed before rc_free, so no completion can run after rc is freed. No new lock ordering is introduced.
-
CVE-2026-99467
In the Linux kernel, the following vulnerability has been resolved: media: marvell: mcam: stop DMA and cancel s_bh_work before freeing DMA buffers In vmalloc mode the frame-completion IRQ queues mcam_frame_work() on cam->s_bh_work, which memcpy()s from the dma_bufs[] that mcam_free_dma_bufs() frees with dma_free_coherent(). mccic_shutdown() frees those buffers without stopping the controller, so while streaming a late frame IRQ can re-arm the work after the buffers are gone, causing a use-after-free. Stop the controller in mccic_shutdown() when streaming is still active (gated on an open fd, which holds a runtime-PM reference, so the device is powered), cancel s_bh_work in mcam_free_dma_bufs(), and move INIT_WORK() into mccic_register() before the device can be published.
-
CVE-2026-99455
In the Linux kernel, the following vulnerability has been resolved: serial: core: shut down initialized port on removal When a serial port configured as a console is opened and subsequently closed, tty_port_shutdown() skips invoking port->ops->shutdown() because port->console is true. As a result, tty_port_initialized() remains true and the port's interrupt handler stays registered in the irq subsystem. If the underlying device is later unbound or removed (e.g. via sysfs driver unbind or device hot-unplug), serial_core_remove_one_port() unregisters the console, frees uport->name via kfree(), and tears down the port without shutting it down or freeing its IRQ. Consequently, the irqaction descriptor remains registered in genirq with action->name pointing to freed memory. This triggers a use-after-free read whenever genirq accesses action->name, such as when reading /proc/interrupts: BUG: KASAN: slab-use-after-free in string+0x476/0x570 Call Trace: string+0x476/0x570 vsnprintf+0x422/0x1300 seq_printf+0x... show_interrupts+... Fix this by acquiring port->mutex in serial_core_remove_one_port() after console unregistration, clearing port->console under the mutex to prevent data races with concurrent tty_port_shutdown(), and invoking uart_shutdown(NULL, state) if the port remains initialized. This ensures that port->ops->shutdown() is called and the IRQ is freed before kfree(uport->name).
-
CVE-2026-99456
In the Linux kernel, the following vulnerability has been resolved: scsi: dc395x: sync the waiting_timer before freeing the host The waiting_timer callback re-arms itself and takes the host lock. adapter_uninit() currently stops it with timer_delete(), which does not wait for a callback already running on another CPU. The final scsi_host_put() that frees the host (and the host lock the callback dereferences) runs right after adapter_uninit(), so a concurrent or just re-armed callback can fire after the free, leaving a potential use-after-free window. Replace timer_delete() with timer_shutdown_sync() at the top of adapter_uninit(), before the host-lock section: the timer is dequeued, a running callback is waited for and rearming is blocked before the chip is halted, so it cannot fire at all once the adapter has ceased to function. Waiting outside the lock avoids the self-deadlock that would result from syncing a callback blocked on the lock we still hold. No shutdown is needed for selto_timer because it has no reachable armer or callback. This issue was found by an in-house static analysis tool.
-
CVE-2026-108314
Tanium addressed an incorrect default permissions vulnerability in Tanium Server.
-
CVE-2026-12040
The FS Poster - WordPress Social media Auto Poster & Scheduler [Facebook, Instagram, Twitter, Pinterest] plugin for WordPress is vulnerable to Server-Side Request Forgery in all versions up to, and including, 8.0.1 via the 'site_url' parameter. This makes it possible for authenticated attackers, with subscriber-level access and above, to make web requests to arbitrary locations originating from the web application and can be used to query and modify information from internal services. The Guzzle HTTP client is instantiated with TLS certificate verification disabled and redirect following enabled by default, allowing redirect-based SSRF bypasses and enabling internal port scanning via distinguishable server responses.
-
CVE-2026-104683
The Envira Gallery WordPress plugin before 1.16.4 does not apply its own gallery-permission policy until an administrator first opens its permissions screen, instead copying gallery-management capabilities onto each role from that role's core post capabilities after activation, which lets Contributor accounts create, edit and delete galleries that the policy is meant to restrict to higher roles.
-
CVE-2026-114975
Vulnerability in the Oracle Hyperion Workspace product of Oracle Hyperion (component: UI and Visualization). The supported version that is affected is 11.2.26.0.000. Easily exploitable vulnerability allows low privileged attacker with network access via HTTP to compromise Oracle Hyperion Workspace. While the vulnerability is in Oracle Hyperion Workspace, attacks may significantly impact additional products (scope change). Successful attacks of this vulnerability can result in unauthorized update, insert or delete access to some of Oracle Hyperion Workspace accessible data as well as unauthorized read access to a subset of Oracle Hyperion Workspace accessible data. CVSS 3.1 Base Score 6.4 (Confidentiality and Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:L/PR:L/UI:N/S:C/C:L/I:L/A:N).
-
CVE-2026-117490
The Flatsome WordPress theme before 3.20.13 does not enforce the acting user's publish and post-type restrictions on an AJAX save action, allowing users with a role as low as Contributor to publish their own content and change its post type (for example to a product) without holding the required capabilities.
-
CVE-2026-24205
NVIDIA TensorRT-LLM for any platform contains a vulnerability where a user may cause a race condition by running concurrent requests. A successful exploit of this vulnerability may lead to data tampering.
-
CVE-2026-99522
In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: avoid use-after-free in icrdma_remove icrdma_remove() dereferences iwdev after calling irdma_ib_unregister_device(): irdma_ib_unregister_device(iwdev) -> ib_unregister_device(&iwdev->ibdev) -> __ib_unregister_device() -> ib_dealloc_device() irdma registers irdma_ib_dealloc_device() as the dealloc_driver callback in its ib_device_ops. The RDMA core explicitly documents ib_unregister_device() that when ops.dealloc_driver is used, ib_dev will be freed upon return from the function. The ib_device is embedded in struct irdma_device and iwdev itself was allocated by ib_alloc_device(irdma_device, ibdev). Consequently, once irdma_ib_unregister_device() returns, iwdev must no longer be dereferenced. However, icrdma_remove() currently accesses iwdev->rf afterwards when deinitializing interrupts, destroying ah_tbl_lock, and freeing rf. Although the final ib_device storage is released with kfree_rcu(), the object lifetime has already ended and callers must not rely on the RCU grace period to continue dereferencing iwdev. Save iwdev->rf before unregistering the RDMA device and use the saved pointer for the remaining cleanup. This issue was found by manual code inspection.
-
CVE-2026-133107
In JetBrains TeamCity before 2026.2.2, 2026.1.6 hTML injection in pipeline notification emails was possible via commit messages
-
CVE-2026-132807
A malicious actor with access to the network and under certain conditions could exploit an Improper Certificate Validation vulnerability found in UniFi Access Application to obtain sensitive information from and make unauthorized changes to an adopted UniFi Access device.
-
CVE-2026-128719
An issue in PHPGurukul Employee Leaves Management System (ELMS) Version 2.1 allows a remote attacker to escalate privileges via the password recovery functionality
-
CVE-2026-127361
Vulnerability in the Oracle Hyperion Financial Close Management product of Oracle Hyperion (component: Reconciliation Manage). The supported version that is affected is 11.2.26.0.000. Difficult to exploit vulnerability allows high privileged attacker with network access via HTTP to compromise Oracle Hyperion Financial Close Management. Successful attacks require human interaction from a person other than the attacker. Successful attacks of this vulnerability can result in unauthorized update, insert or delete access to some of Oracle Hyperion Financial Close Management accessible data. CVSS 3.1 Base Score 2.0 (Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:H/PR:H/UI:R/S:U/C:N/I:L/A:N).
-
CVE-2026-115180
Vulnerability in the Oracle Hyperion Financial Close Management product of Oracle Hyperion (component: Reconciliation Manage). The supported version that is affected is 11.2.26.0.000. Difficult to exploit vulnerability allows unauthenticated attacker with access to the physical communication segment attached to the hardware where the Oracle Hyperion Financial Close Management executes to compromise Oracle Hyperion Financial Close Management. Successful attacks of this vulnerability can result in unauthorized read access to a subset of Oracle Hyperion Financial Close Management accessible data. CVSS 3.1 Base Score 3.1 (Confidentiality impacts). CVSS Vector: (CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:L/I:N/A:N).
-
CVE-2026-115132
Vulnerability in the Oracle Hyperion Planning product of Oracle Hyperion (component: Security). The supported version that is affected is 11.2.26.0.000. Easily exploitable vulnerability allows unauthenticated attacker with network access via HTTP to compromise Oracle Hyperion Planning. Successful attacks require human interaction from a person other than the attacker. Successful attacks of this vulnerability can result in unauthorized creation, deletion or modification access to critical data or all Oracle Hyperion Planning accessible data. CVSS 3.1 Base Score 6.5 (Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:L/PR:N/UI:R/S:U/C:N/I:H/A:N).
-
CVE-2026-115083
Vulnerability in the Oracle Hyperion Infrastructure Technology product of Oracle Hyperion (component: Installation and Configuration). The supported version that is affected is 11.2.26.0.000. Difficult to exploit vulnerability allows unauthenticated attacker with network access via HTTP to compromise Oracle Hyperion Infrastructure Technology. Successful attacks require human interaction from a person other than the attacker and while the vulnerability is in Oracle Hyperion Infrastructure Technology, attacks may significantly impact additional products (scope change). Successful attacks of this vulnerability can result in unauthorized update, insert or delete access to some of Oracle Hyperion Infrastructure Technology accessible data as well as unauthorized read access to a subset of Oracle Hyperion Infrastructure Technology accessible data. CVSS 3.1 Base Score 4.7 (Confidentiality and Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:H/PR:N/UI:R/S:C/C:L/I:L/A:N).
-
CVE-2026-115022
Vulnerability in the Oracle Hyperion Data Relationship Management product of Oracle Hyperion (component: Access and security). The supported version that is affected is 11.2.26.0.000. Easily exploitable vulnerability allows unauthenticated attacker with network access via HTTP to compromise Oracle Hyperion Data Relationship Management. Successful attacks require human interaction from a person other than the attacker. Successful attacks of this vulnerability can result in unauthorized creation, deletion or modification access to critical data or all Oracle Hyperion Data Relationship Management accessible data. CVSS 3.1 Base Score 6.5 (Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:L/PR:N/UI:R/S:U/C:N/I:H/A:N).
-
CVE-2026-77942
A maliciously crafted IES file, when parsed through Autodesk AutoCAD, can force an Out-of-Bounds Write vulnerability. A malicious actor can leverage this vulnerability to cause a crash or execute arbitrary code in the context of the current process.
-
CVE-2026-18826
A maliciously crafted DXF file, when parsed through Autodesk AutoCAD, can force a Type Confusion vulnerability. A malicious actor can leverage this vulnerability to cause a crash or execute arbitrary code in the context of the current process.
CVE records published in 2026 (ids starting CVE-2026-), sorted by how likely they are to be exploited.